-
Unable to find the link option when using maschine plus on standalone mode
I updated my maschine plus recently and now I’m unable to find the link option when using my maschine plus on standalone mode. Then when i use it via USB, Maschine and traktor links but doesn’t seem to sync. Please advice on how i could resolve this Thank you
-
Central Library on M+ Standalone 3.3.1 Contents?
What parts of the Central Library can be used for the Maschine+ Standalone? Can you be more specific?
-
Maschine+ Set midi note per pad?
Is there any way to have two pads respond to the same midi note? I would like to be able to have incoming midi (not patterns) trigger all pads, and then solo particular sounds I want to hear. Linked pads don't work this way, at all. I don't see any way to set the midi note that pads 'receive'. Possibly there is no way to…
-
Problems with Micro-SD-Cards in maschine+
The following problems occurred: The original SD card (Micro SD) still had 5 GB of remaining capacity; Maschine+ refused further expansion, even though it was only 1.2 GB in size. All previous expansions suddenly disappeared; Maschine+ displayed: "SD card unreadable." Therefore, a 128 GB Sandisk Extreme V30 Micro SD card…
-
Compatibility of Kontrol MK3 with Maschine Plus, Maschine 3, etc...
Hello Community Does S49 MK3 keyboard integrate 100% with Maschine+, Hardware, and Maschine 3, Software? I have actually the S49 MK2 keyboard and it works perfectly. I would like to upgrade to the S49 MK3 keyboard. Can I change without problems? Thank everybody…
-
Smart Strum in Chords Mode
Hello community, I'm a Maschine+ standalone user and I'd like to propose an improvement that I think would greatly expand creativity for those of us who compose music without advanced music theory. I'm referring to implementing a "Smart Strum" feature within Chords mode, allowing you to use the Smart Strip to break down…
-
Issue with Behringer UMC1820 and ADA8200 into Maschine Plus standalone
Hello all, I am running into an issue attempting to connect a UMC1820\ADA8200 into a Maschine+ in Standalone mode. The 1820 and 8200 are connected with two ADAT cables, and everything appears to work OK into an iPad with AUM (all 20 input channels are recognized and pass signal when selected). If the setup is then plugged…
-
Bounce in place - M+
I'm trying to figure out the difference between the bounce-in-place feature implemented in the latest M+ update and resampling the old-fashioned way. Is the result the same, or am I wrong? Can someone more knowledgeable explain the possible differences and/or conveniences of the much-vaunted bounce feature? Thanks a lot.
-
Maschine+ Startup Issues
Is Native Instruments EVER going to fix start-up issues with Maschine+ ??? My Maschine+, which is less than two months old, isn't booting up properly 90% of the time. It just cycles through the startup screen indefinitely without ever actually starting. NI has sent me this "solution," which doesn't work. Please download…
-
Clock Synchronization Issue Between Maschine 3 and Virus TI2 via USB
Hello, I am experiencing a clock synchronization issue between Maschine 3 and Virus TI2 connected via USB. The problem is as follows: Virus TI2 is controlled through the Virus Control application inside Maschine 3. In Maschine, I have a kick set on every beat, which plays perfectly in time with the metronome, but the Virus…
-
controller not connecting to Mac
mk3 controller not connecting to Mac computer mini 5 since I up grade 1.9
-
3.3.1(R0)
maschine+ users do your about page say3.3.1(R0)? what do the ro mean. i currently also cant import mp3s.
-
Maschine plus Update 3.3.1 ist FAIL
After the update to V3.3.1 runs everything NOT like before! the update can not testet from native to performance! My liveset was with 2.18 perfect! And now? You put 2-3 pads too mutch und always freezes! My Maschine Jam as second controller freezed as well!! DOWNGRADE!!!!!! Support: Where are you??? I have opened two…
-
Problem with recording vocals
Hi, I have problem with recording vocal, all settings are ok in my opinion, then i push the START to record, I see all time waitin for next but - and there is no possibility to start record. Any sugestions guys?
-
Maschine + Plus freezes after update . How to downgrade?
Hi friends, I have updated my Maschine Plus to the latest version, and when I try to load the project I was working on, it freezes. The only solution is to re-boot it. I have a concert on Friday. Please help me roll back to the previous version. Thank you.