-
Brand-new MK3, can't get my sound to work. Please help!
Hi everyone, So I just bought my MK3 but this first day has been quite a frustrating experience. Long story short: I'm unable to get ANY sound by plugging in headphones in the phones jack. I'm on Mac OS Big Sur 11.6. Sony MDR plugged in + sound knob at the back turned on Maschine MK3 as Device (CoreAudio Driver) Input L &…
-
No aftertouch in Maschine
I made a nice preset in Super 8 where I use aftertouch to give a bit of pitch and filter modulation. Works great in Presonus Studio One. I used the same Super 8 patch in Maschine today and it turned out the aftertouch isn't working. After a while I found out that Maschine isn't supporting aftertouch. Is this for real! Why?…
-
Software vs hardware
Hi all. I'm new to the synth world. I have bought some NI and Arturia gear recently which all comes with software synths. They all sound pretty amazing to my untrained ear. I just wondered are these software synths good for professional recording and do people actually use them? Are there any famous hits that use them that…
-
The Touchstrip never release.
Hi, all. The touchstrip never release, If the touchstrip Engage is OFF never changes to On when I press the touchstrip, only change the parameters like Frequency or Feedback. I don't know if is a bug or an issue with the touchstrip.
-
Please confirm Maschine can't route MIDI from a VST/AU plugin?
I'm trying to route MIDI output from a VST plugin (Hypercyclic, Tonespace or Reaktor) to another instrument in Maschine and I can't figure this out. Tutorials I've found online suggest using either a physical MIDI loopback cable (??) or the IAC Driver on Mac, but both of these solutions really get in the way. Is there…
-
Routing Play Series Drums to Multi Outs
If you've interested in routing your Play Series Drum Kits to individual output channels...you're in luck! Load your Play Series Drum Kit on Pad 1 of a Group and follow the steps below VERY CAREFULLY in the Maschine software or your Hardware Controller (Maschine MK3, Maschine+, or Mikro MK3 : Step 1: Set up "Multi Outputs"…
-
Maschine MK3 problem in Logic Pro 10.8?
Anybody else not able to get Logic to receive midi input from Maschine MK3? In midi mode Logic shows an input in the midi input meter but no midi output signal and I get no audio. In channel mode I get audio signal in Logic but no midi. I've tried everything, nothing works. Anybody got any ideas?
-
No sound from Adam T5V Monitors with Maschine MK 3
Hello my friends! My set up is as follows: Maschine connected to a Windows 11 PC with a USB cable. 2 monitors are connected to Maschine L and R out using XLR to TRS cables. In Maschine 2 -> Preferences -> Audio Driver: ASIO Device: Maschine MK3 Status: Running Sample Rate: 44100 In output it is assigned to Main L and Main…
-
Ozone 10 is not working on maschine mk3 after vst3 update
Maschine mk3 updated to latest vst3 update. It shows ozone 10 icons but when clicked it states cannot load ozone 10. Why? Since ozone 9 is working fine.
-
Maschine manual errors: Pattern Arrange mode & creating Clips
The Maschine MK3 manual, both online and PDF, has a couple of errors apparently stemming from the 2.12 update's addition of Clips and the introduction of Maschine+. Firstly, in Working with Patterns and Clips / Patten Basics / Pattern Editor Overview, under Patterns on the Controller, it describes a mode called Pattern…
-
When using an audio file and stretching it to the desire length and it goes pass the set measure.
When using an audio file on the timeline/in a measure and I stretch the audio file and it goes pass my measure point, why can't it be trim to fit into the measure. This causes a lot of frustration for me. Will there be some kind fix for this?
-
What is the future of Maschine mk3?
We've now seen the rollout of the S-Series keyboards. As far as I know, MK2 keybaords are still supported with new iterations of the Komplete Kontrol software. Meanitme, we're seeing a number of rumours about a new Maschine. Will Mk3 Maschines continue to be supported, and will they also benefit from the new software and…
-
Maschine software
My question is what is being done to update maschine daw software to continue to build and compete with other daws like logic and fl studio? I have noticed that maschine gets mentioned the least as a daw and I assume it is bc it can be worked as a vst but I believe this is a area of opportunity to keep things inhouse so…
-
Maschine MK3 not showing Ableton Live 10 clips in Session View
Hi community! I've followed the instructions for installing the Maschine Mk3 Control Script/Template into Ableton Live that is posted here: https://support.native-instruments.com/hc/en-us/articles/4413367278097-How-to-Install-MASCHINE-Templates-for-Ableton-Live And while the transport controls now work great, the clip…
-
Is it possible to mute mk3 sounds or groups with an external midi controller using cc ?
Hallo, I'm using a soft step 2 foot controller via usb midi (MacBook pro) to control some parameter of a Maschine mk3, changing scenes for example. Is there a way to mute a group or a single sound by using cc commands that have been sent from the soft step? Thanks for help or workarounds!