-
Maschine Plus stuck at start up screen after firmware update.
just upgraded to a Maschine+ so I could finally work in true standalone mode. After successfully updating the firmware to 1.6.1, my unit is now completely stuck in an infinite startup loop. This issue started on Friday, and despite submitting two support tickets, I’ve been left with zero solutions and now have to wait the…
-
Making Editing Easier
In Events view, allow Shift + 4‑way encoder up/down to move selected events to previous/next Sound slot (within the same Group), instead of only changing selection. Hello Community, Greetings from Greece! I hope you doing great! I' m a Graphic Designer from Greece and I Love to Make Beats. I' m Producing since 2005 mostly…
-
Anyone copy a project from hardware to software and had changes in the mix?
I've opened a large project built on the M+ using 3.4.2. It was originally started on version 2, but seemed to open in 3.4.2 fine. I copied this to my computer to open it in the Maschine Software. Some sounds are way too quiet. The mix settings are identical, but in some cases, the sound is just quieter, in other cases, it…
-
Maschine+ stuck on “MASCHINE+ is starting” after formatting original SD card
Hi everyone, I’m looking for help with a Maschine+ that is now permanently stuck on the “MASCHINE+ is starting” screen during boot. The unit was purchased in 2023 and has seen very little actual use. It also remained unused/stored for a long period (almost 2 years) before I recently tried powering it on again. The…
-
Maschine 3.5 or is there a release?
Strange there a decent update but no one is talking about it at all.. is this forum dead and where are the influencers post?
-
Hardware Support Ticket [#4861740]
Hello, NI support team @Jeremy_NI I am writing to request a status update on my support ticket #4861740. I reported a hardware defect (severe encoder jitter) on my Maschine+ last two week. I have already provided all requested information to the hardware support team on Monday, April 13th I haven't received any response…
-
matrix maschine
What I call “Matrix Mode” in Maschine is basically a live arrangement workflow built around Groups and Lock States. The idea is to organize the project so that each main element has its own Group, for example drums in Group A, bass or melody in Group B, textures in C, vocals or FX in D and so on. Once the instrumental…
-
THE MASCHINE FLOW TECHNIQUE
THE MASCHINE FLOW TECHNIQUE1) BASE STRUCTURE (GROUPS) Each group has a specific role within the system: [A] DRUMS [B] BASS [C] INSTRUMENT [D] INSTRUMENT 2 / MELODY [E] FX 1 (Perform FX) [F] FX 2 (Perform FX) [G] SYNTHS / POLY SYNTH [H] AUDIO RECORD (internal recording) This structure can be expanded depending on your…
-
Maschine Plus clock pass through
Simple question really: if I've got maschine + set to midi clock slave, can it pass through the received clock to external synths attached via USB? It doesn't appear to. Sorry if this has been asked a million times before… I did search beforehand but didn't turn anything up.
-
Machine + update - invalid signature mmcblk
I cant seem to update my Machine + I've tried factory resetting - didnt solve the problem I've tried a fresh SD card 64GB, - didnt solve the problem I've tried putting the file" system-reset-v2.nut" on both SD cards in the root - didnt solve the problem. I tried deleting the partition on my second SD card and inserting it…
-
Use audio inputs when Maschine is a plug-in
With the Maschine V3 software, I can route audio from my interface into Maschine, and process with effects etc. When I load Maschine as a plug-in within Logic, this doesn't seem to work. Same audio settings, and I can see it's using my RME interface because it shows 16 inputs (not the 4 on the Maschine Hardware). But no…
-
Machine + register transfer
Hello everyone. So, I recently got a Maschine Plus in an eBay auction. Upon receiving and trying to set it up, it's clear it's still registered in someone else's name, and I can't use it in standalone mode, which is why I bought it. I contacted the seller, and they said they purchased it from someone else, so they can't…
-
How to apply the 5 for $55 discount?
I added the products to the cart, went to check out and the full price remains and today is APRIL 30TH the sale ends MAY 17
-
How long does license transfer take?
I recently purchased a machine studio and the dude I bought it from put in a transfer request yesterday and still hasn’t heard anything back so I’m curious how long it generally takes? I made a ticket and they didn’t answer my questions both times. I even sent them the email from the account that’s requesting to be…
-
List of Maschine features no longer available in version 3
Before updating to Maschine software Version 3, I waited, and checked the forums looking for issues and problems. I saw some people had issues, but nothing that worried me. What I did not find was a post listing the various features available in V2 that are no longer available in V3. So I updated, and of course now wish I…