-
Maschine Jam MK2
Native Instruments, are there ANY plans in the works for an MK2 for the Jam along the lines of an Ableton Push 2? I got one shortly after it dropped and I would NEVER part with it! My MK3 and Jam are side by side and I constantly bounce between the two. I even remapped it to be used as an additional control for Traktor! I…
-
Maschine Jam in 2022?
Hello boys and girls, I hope you are all doing well. Although this has been asked by many, I would like your opinion on whether it is worth buying a (used) Maschine Jam in 2022. Since this decision depends on a number of things, let me inform you about the way I usually work, the hardware I have and the intended use for…
-
Controller Editor Wizard wanted
Hey everyone out there in Canland. I have been struggling to figure out how to use the controller editor software to make my Maschine Jam a more fleshed-out controller surface for Logic Pro X. If anyone has experience and is willing to teach a man to fish I would be most grateful. I mainly want to figure out how to make…
-
Is there a way to select all notes from JAM in event or step mode?
FEATURE REQUEST IF NOT. It can get tedious navigating between pages on the jam looking for that specific note/event you want to edit. Its also a killer to workflow if you wanted to nudge your whole pattern over a bit from the hardware. Currently have to move each note individually. I haven't found a workaround besides…
-
How to nudge note / event steps on Maschine Jam?
Section 7.4.5 of the Maschine Jam manual talks about Nudging Events in a Pattern, but it doesn't say how to actually nudge the events. I see that you can set the Step grid and the Nudge grid from the Jam controller, but I can't figure out how to actually nudge them according to the Nudge grid. I know there is a function…
-
Is there a way to turn off Native Instruments Controllers without Unplugging them?
Hello! Is there a way to turn off instruments such as the Maschine Jam or Komplete Kontrol M32 without unplugging them? My Maschine MK3 has a power button on the side, so that's how I keep it plugged in but off when I'm not using it, but with my JAM and Komplete keyboard I have to unplug/plug them back in every time I want…
-
Jam pattern buttons don't correlate in Song mode?
Unless I'm missing a setting option somewhere, I have noticed that when the Maschine Jam is playing back a project in Song mode, the pattern buttons don't seem to change to reflect the currently active pattern in each group in the current position of the song being played back. But it would certainly be helpful if it did…
-
Maschine Jam - wow (late to the partay)
Wow I finally caved in and got a second hand JAM, so blown away by it, I was apprehensive since I'm on a M1 mac but so far all is good. MAJOR KUDOS to the NI team and damn I should have got one before! If anyone has any fave tutorials then please share, as I know there is a lot of hidden functionality in there. Thankyou NI
-
Does the Maschine JAM still work with the Maschine MK3
really would like to add the Maschine Jam to my MK3 workload. Noticed today it’s discontinued by NI (why I have no idea). Does it still work fine on current 2022 firmware? Also does it work with Maschine+?
-
MK3 in PAD mode, JAM in the KEYBOARD mode
Dear all, please advice is it possible to use Maschine MK3 in KEYBOARD mode with Maschine JAM in PAD mode. Or vice versa. Now these two Maschines work synchronized. If I select PAD mode, both Maschines are switched into the PAD mode. Is there any way to switch them.
-
Studio Setup, Workflow and Support
I'm looking for someone who is knowledgeable and could hire/book for some setup and workflow Seshions. Current home studio hardware: I-Mac, Maschine Mk3, Maschine Jam, Komplete Control S61 and a few other components. Software Logic Pro. I have a few questions about the workflow, interfaces or midi data transfer between…
-
Is there a shortcut to access the Maschine Jam templates!!
i know that you can access them via the controller editor... but is there a shortcut via midi keypresses to cycle through the Maschine Jam templates i have created i know that Maschine Jam can change the Maschine instances you are using(jumping between VST and stand alone)... but thats different... i know on the maschine…
-
NA 2.0.3 messed up my Maschine installation
No formatter is installed for the format not-found
-
Maschine JAM no longer recognised in Windows 10
So I've had a raft of Windows updates and my Maschine JAM no longer appears in Device Manager, and the Maschine software no longer sees it, on either of my two laptops. If I try plugging in the JAM while Maschine is running there's a lot of pained crackling and then it gives up. When I first plug in the JAM all the lights…
-
midi controllers using the same scale type
Hi,idk how but sometimes , my midi keyboard casio, use the same scale type that i use/setup in mk2 or jam, like native controllers, he use the same scale when i play so....Any knows how to do this ? Coz now i have a keystation mk3 but didnt happend. Thank you !