Maschine Software Will Not Show Up In Native Access

24

Answers

  • Matt35000
    Matt35000 Member Posts: 2 Newcomer

    Hello. In the same camp....I just purchased a new MASCHINE MIKRO MK3 and had no problem registering it. I can see the registered device serial number and the software package online in my Native Instruments account but for some reason it does not appear in Native Access. And therefore I cannot download/install the software necessary to enable the device.

    I am on an M1 Ultra Mac running Sonoma 14.2.1. 

    Please advise on next steps on how to get the software package installed.

    Thanks! 

  • Jeremy_NI
    Jeremy_NI Customer Care Posts: 12,467 mod

    @Matt35000 Please reach out to our dedicated support agents: https://bit.ly/NI_support_NA

  • tanerbay404
    tanerbay404 Member Posts: 1 Newcomer

    I am trying to install Maschine software for an old MK2, but it does not sh ow up in Native access. Can someone help?

  • Jeremy_NI
    Jeremy_NI Customer Care Posts: 12,467 mod

    @tanerbay404 What is your operating system? What version of the Maschine software are you trying to install?

  • retroantix
    retroantix Member Posts: 2 Newcomer

    I am having this exact same issue. I have had the Mikro Mk3 since December but just unboxed it today and I only see

    Screenshot 2024-03-16 at 12.27.13 PM.png

    I installed what I could but every single tutorial to setup points to installing:

    Screenshot 2024-03-16 at 12.30.03 PM.png

    but they don't appear for me at all. is tehre something I need to do or something that needs done to my account to fix this?

  • retroantix
    retroantix Member Posts: 2 Newcomer
    https://community.native-instruments.com/discussion/comment/140923#Comment_140923

    oddly enough shortly after I posted this it all just showed up after hours of fighting with it, appears to be resolved.

  • noreaster171
    noreaster171 Member Posts: 2 Newcomer

    I have the same issue and have tried the same general steps (re-install NA 2, re-auth, re-connect, etc.) - @Jeremy_NI any ability to provide assistance would be amazing!

  • noreaster171
    noreaster171 Member Posts: 2 Newcomer

    I already have a ticket open (#4263081), but they haven't been able to help.

  • Jeremy_NI
    Jeremy_NI Customer Care Posts: 12,467 mod

    @noreaster171 My colleagues will get back to you as soon as possible.

  • KrOmE O
    KrOmE O Member Posts: 1 Newcomer

    Ya same issue, Dusted off the Mk2 for some Traktor integration and native access wont show maschine in the software downloads. Windows 10 is my operating system.

  • PatL3wis
    PatL3wis Member Posts: 1 Newcomer

    Hello, I'm having the same issue. Dusted off the old MK2 and can't find the Maschine software in Native Access… any help would be great, thanks!

  • Jeremy_NI
    Jeremy_NI Customer Care Posts: 12,467 mod

    @KrOmE O @PatL3wis I guess you are looking for Maschine 1 software. It is possible to install the Maschine 1.8 but it was discontiinued some time ago and will not work on most recent Mac Os systems. You might need to update to Maschine 2 software.

  • Jiang li Feng
    Jiang li Feng Member Posts: 22 Member

    SAME PROBLEM and its not showing up in my registered products list. the hardware and software isnt and i have a MK3. i was litterally using maschine 2 until i restted my pc and its been weeks now of it not showing up and it wont let me re register the hardware again its telling me its already been registered

  • joshadams46
    joshadams46 Member Posts: 1 Newcomer

    im having the same problem with my account

  • Jeremy_NI
    Jeremy_NI Customer Care Posts: 12,467 mod
    https://community.native-instruments.com/discussion/comment/181907#Comment_181907

    Ok but what is the specific issue, did you buy a device and didn't get the software? Is it a second hand device, new? Bought where? Have you tried to contact our support? https://bit.ly/NI_support_NA

Back To Top

Categories