What’s New in Maschine+ 1.6.1
Comments
-
So,i am trying to update on the new 1.6.1 on the plus with no luck.
Here is what i did.
1. downloaded the system update (successfully)
2.after the download has finished i am getting the prompt that the system update is ready for installation.
3.hit the option to install.(maschine is updating and then restarting)
after the restart i am getting the following message "No updates have been found"
after 5-6 attempts i still got the same message.restarting the device is still showing 1.5.1.0
a full reset on the device is not make a difference.i don't know what else can i do.
it should be an easy task but unfortunatelly i am not able to install it.
any ideas anyone?
thanks in advance.
0 -
Try what unbrokendub wrote in previous page (using SHIFT button) to see if the Install prompt will be re-offered
0 -
Hi @MaikR. Could you please write me in private? I have something to ask you, but being your account a private one I can’t write you
0 -
If so, than please add the option to leave this kind of bloatware from the device…
3 -
That helped and finally i was able to install.Thanks so much.
3 -
That failed the last time they tried it (With sounds.com), bro. It was a total crash and burn that was an utter waste of development time, and all of us oldheads are still upset about it.
2 -
My Maschine+ just took a while to start and asked me if I wanted it updated. I had applied the update right away when it came out last week, and have been using it daily. Just saw this message today. I let it run through the update just now and it started fine after reboot. Just wanted to see if that’s normal, like there was a mini patch update between yesterday and today? Anyone else encounter this? Can’t remember what was the version before, now it’s 1.6.1.24
0 -
If you read previous posts, you’ll see a couple more reported having to run the update a second time
0 -
yes, the mono left / right / center option would be great. also a sample playback option for stereo/mono would be needed.
i wish they would work a little bit on the sampler and and add some small nice workflow improvements. couldnt care less about stem separation, as there are more than enough tools to do it and i think it's too cpu intensive for the maschine+.2 -
Please get in touch with our support here: https://bit.ly/NI_support_maschine
0 -
Issue solved.i was able to install it after some attempts.Thanks a lot!
0 -
That's great to hear!
0 -
Hi @naturaldichotomy
At the moment, there are no plans to release Guitar Rig Lite on Maschine+, but we are actively evaluating a broad list of content for future compatibility. Some of the more CPU-intensive instruments and effects will be made available with Maschine 3 on Plus, since it includes bounce-in-place, which helps manage heavier projects more efficiently.5 -
Since the introduction of Bite, Dirt etc. it would be nice to see a few more from the collection….
Driver, Enhanced/Passive EQ, RC24/48, Solid Bus Comp, Solid Dynamics, Solid EQ, Supercharger/GT, Transient Master, Vari Comp, VC160, VC2A, VC76
4
Categories
- All Categories
- 18 Welcome
- 1.6K Hangout
- 66 NI News
- 859 Tech Talks
- 4.4K Native Access
- 17.6K Komplete
- 2.1K Komplete General
- 4.6K Komplete Kontrol
- 6.1K Kontakt
- 1.6K Reaktor
- 398 Battery 4
- 888 Guitar Rig & FX
- 453 Massive X & Synths
- 1.4K Other Software & Hardware
- 6.2K Maschine
- 7.8K Traktor
- 7.8K Traktor Software & Hardware
- Check out everything you can do
- Create an account
- See member benefits
- Answer questions
- Ask the community
- See product news
- Connect with creators