-
Freezes on startup Maschine plus
Yesterday I bought a second-hand Maschine plus. Unfortunately, it cannot be started separately. It says that Maschine plus starts. When I connect the USB cable, it works, but I start it normally. When I disconnect the USB and connect it separately, it freezes. I bought it with the box and accessories. I updated the…
-
Why isn't Maschine software available
This has been asked over the past couple years it seems. I purchased, brand new, a Maschine MK3 and I am struggling to understand or figure out why I can't download the Maschine software. Make sure the OS is up to date? Check. Restart Native Access? Check. Make sure it's all registered correctly? Triple checked. Even…
-
No Maschine Software in NA
Hi, I hope anybody can help me out. I bought the Mikro MK3 second hand. I downloaded NA and registered with the already transferred serial number. However, the Maschine software is not appearing in NA. I only see 8 players in my library (eg Monark, Controller Editor, etc). I also deleted the xml as it was suggested.…
-
Maschine not connecting to software
Hi. I have a masschine mk3 running 1.4.5 firmware driver. It stopped connecting to my sofware. My mac detects that it is connected. I know this because my audio midi setup is connected. Also, I used the "maschine mk3 updater" and it detects that the controller is connected and updated. I suspect this could be related to me…
-
Maschine MK3 - nothing is working
I need help to start this on a new computer nothing works. The Maschine is useless the browser does not work. I'm sure it is simple but at the moment I can't use anything and you don't help!!!!!!!!!! [EDIT by Moderator - duplicate discussion content inserted below] How to activate Maschine MK3 At the moment nothing is…
-
Maschine3 Audio problems
By the way: not possible to open cases? The chat is catastrophic. Now i have problems with maschine3 to run a rolling bassline with serum and compressor sidechain.. Maschine hangs a lot for msecs while playing this simple loop. I changed to maschine 2 and have no problems.
-
Maschine 3 - Not available for download (2)
Hello, I purchased the bundle with the maschine 3 update but only the maschine 3 does not show up in native access please help
-
Maschine mikro mk3 cannot see the software
Just receievd my new Maschine mikro mk3 and when I registered the serial in native access I cannot find the new software it came with i.e MASCHINE Essentials Which I assume would install the Maschine software. I will tend to use it as a vst via ableton but I inderstand i need to start the standalone software first. but…
-
License locked for 60 days
Q: Translation inserted by Moderator (translation by DeepL) I need to transfer the licence, but I can't because 60 days have not yet passed how can I do it? Community Code of Conduct - Please read before posting : Quote : Our community is currently only available in English. Please be advised that we retain the right to…
-
New Maschine 3 software Gui
I'm not really feeling the color choice. It makes it very difficult to see at times, especially early in the day when I have tons of sunlight shinning in my window.
-
Short Cut Keys
Please excuse my ignorance here, but I am new to Maschine. I am not a musician so a lot of what I will be doing is programming things in via the computer. I am looking for short cut keys to navigate through a track. I understand that you can go from note to note using the arrow keys but that doesn't seem to allow to moving…
-
Maschine 3 and Komplete Control S49 MK2
Hi Everyone, I have Maschine hardware controller and Komplete Kontrol S49 mk 2 that integrates well with Maschine 2 software. I have deliberately not purchased S49 mk 3 because of loss of functionality. Does anyone know if Maschine 3 software still integrates properly with the older S series controllers? I've seen Maschine…
-
Two quick questions about Maschine 3.0 update
Hi! Quick question — is it possible to keep Maschine 2.0 software on the same computer as Maschine 3.0? And is there any hardware that’s not supported in 3.0? I use a MK3 with the Maschine Jam and Komplete A61 Nervous to jump into 3.0 after finally getting some footing in 2.0 and I don’t want to jeopardize the projects I’m…
-
Maschine 3 update - installation failed
I followed the different steps to give the full access to the hardrive but the installation of Maschine 3 is failed. What should I do ?
-
Autosampler in Maschine 3.0 - Save with Samples greyed out
Hello together, I just tried today the functionality of Auto Sampler in Maschine 3.0 and everything recorded nicely. But when I tried to Save with Samples everything is greyed out. Did I miss something? Best regards, Sedat
-
loop function doubles
Hello, My loop function isnt working properly in Maschine 3.0. When the loop ends it doubles at the beginning like the loop isnt lined up correctly. Im hoping this is bug that needs to get fixed.
-
Maschine3 looks pixelated
Why is so? Why no high res UI in Maschine 3.0?
-
[Maschine 3.01] Unable to browse my OneDrive files
I have installed the last Maschine 3 software and I dont see my OneDrive directory structure and files in the Files Browser of Maschine. Apparantly, this is an old issue known in v2.18 … Any Idea ?
-
How to deactivate my maschine mk2 from the previous owner?
I bought used maschine mk2 few years ago and tried to activate the hardware in order to get free maschine software but it says that it's already registered, the problem is that the previous owner is not available to get in contact with.
-
Why am I getting maschine error messages?
Just started getting these messages in my Maschine working with pro tools. Error massive could not be loaded. It's doing this with several of my owned software..Prism, Mouth.. I notice that Kontakt doesn't load everything anymore too. Can someone please help?