-
How to split a stereo signal inside Maschine?
I am cooking up something on the Reaktor M+ dept again.. and now, in testing, I am stumped with a problem of stereo splitting a signal in Maschine? I want to be able to split the output of a sound or a group, into two destinations. One destination carries on the left channel signal, while another carries on the right…
-
Maschine sound expansions for POP/Rock/Funk music
Hello community, I would like to precise that I'm a complete beginner in Maschine software and in music production in general. Considering that I'm try learning finger drumming, recently I bought a Maschine Mikro MK3 mainly for the famous quality of their Pads ignoring the fact that the system is a lot more than this. So,…
-
How to access Minifreak V user bank of presets
Hi everyone, I am brand new to Maschine Mk3 and to this forum. Hopefully I am asking a relevant question and not one due to my stupidity! I only see presets from the factory bank within the plugin browser on Maschine. I have a user bank that contains all my Minifreak presets but I cannot see a way to access these presents…
-
Maschine 3 does not run properly on Windows 11
Hello world, I just bought Maschine 3.0 upgrade and the quality of experience is clearly not there. I'm experiencing frequent sound distortions and pad hits are not always properly recorded. It was clearly not the case with the version 2.8. I'm considering rolling back on 2.8 but I already paid for the upgrade… I'm I…
-
Machine with piano keyboard
Has there been any talk about native instruments releasing a standalone Machine device with a built-in piano keyboard, like the Akai MPC key 37?
-
Sequioa compatibility clarification with audio 6 mk2?
Hey guys, I see that audio 6/10 are compatible with the new OS but is the audio6 mk2? I am unsure if that comment refers to all audio 6 devices or just the mk1 for the moment, I think everything else I need is ready for upgrade but if my sound card bonks out that means no work at all getting done, thanks!
-
Another slap-in-the-face to us M+ owners from our loveless NI parents.
Soooooo, years go by with us asking please please please allow us to buy M+ compatible variants of the Komplete Keyboard plugins… and what do you guys do to your freakishly loyal M+ (flagship Maschine) owners?? You allow your competitors… MPC/Akai compatibility but not us. Devices that have much worse specs (besides the…
-
Can’t seem to move groups, drag and drop, etc.
I can’t seem to move patterns in the arranger. Cant move groups up or down in arranger. Can’t even move sounds in the group view. Can’t drag and drop sounds into groups either. I’m not sure what is the issue. I also have a red icon when I try to do anything of that nature.
-
Maschine Mikro 3 templates have different file formats in macOS and Windows???
This is puzzling to me and I hope there's some conversion tool or something because it makes no sense to me. I had made several templates for the Mikro 3 on my Mac, for different instruments, and some just to have different colors for each page. Recently I built a PC. When I got around to install the Controller Editor app,…
-
Issues with Maschine 2 Plug-In and Maschine Mikro MK3 in Logic Pro
Hi there, I'm experiencing an issue with the Maschine 2 Plug-In in Logic Pro and the Maschine Mikro MK3, which I haven't been able to resolve yet. In my project, I've set up a bussing system to route each pad to a separate track (similar to the tutorial I watched - https://www.youtube.com/watch?v=-e9kAilOzOU&t=1s).…
-
Komplete 15 Select on Maschine Plus: Is it compatible?
Hi everyone, I'm trying to figure out if Komplete 15 Select can be installed directly on Maschine Plus. Has anyone done this successfully? Are there any known compatibility issues or specific steps I should follow? Any advice would be greatly appreciated!
-
Midi feedback in maschine mk2
I'm using my maschione mk2 as a midi controller, but I can't configure it to receive the midi from the automations that I've written. I mean, I can use it to write, perfect, but then I don't see the automations or the midi that I've written played on the pads, knobs or buttons. I think this is called midi feedback. I work…
-
Maschine MK3. Seqoia 15.3 M2 Max
so I have a lot of packs and expansions. However. When I turn on my DAW/Mk3. Under the Browser. I only se 3. At the top. It seems I can access them. But I dot see them on my DAW. Is this a setting issue?
-
Maschine 3.0 General Discussion
Hi, Many want improvement on the new maschine 3.0.. of course stems which have been done already and nothing ground breaking will be the big push alone with .mp3 support which is over a decade old.. also better arrangement which is over 5 plus years old.. another not popular feature which I'm sure has not been addressed is…
-
Maschine 2.18.4 Won't Play in Standalone
When I click play in the software, it will not play the selected pattern, and does not show the play bar moving across the pattern. If recording is active and I hit a note it will record that note at various positions in the pattern, but it still never plays back the pattern. MIDI Sync is turned off in the settings. I'm…
-
Why can't I see Latin Beats Leap in Maschine Mk3?
Hey all, it's been a few days since I got my Maschine MK3 and installed everything that came with it. I bought the Latin Beats Leap for Kontakt 8 and saw in a video from NI that it could be loaded into a sound and then played from there. However, I'm not entirely sure how to do that. I've loaded Kontakt 8 into sound 1.…
-
Maschine Drag and Drop Bouncing Feature Expansion
As someone who uses Maschine primarily as a plugin in the DAW, my workflow generally leads to all parts being exported with the drag-and-drop audio bouncing feature. I like to have everything separate to I tend to go through all the parts and solo them before dragging the bounced scene out. This can be a bit tedious so I…
-
How to send Maschine 3.0 projects to Maschine Plus Standalone?
At the moment I can't transfer Maschine 3.0 desktop projects to my Maschine Plus Standalone for performance or working on a song while I'm not in the studio. That's really annoying because going back and forth between desktop and mobile is an important part of my workflow and one of the reasons using Maschine! Did anyone…
-
Reinstall MASCHINE?
Is it possible that if I reinstall MASCHINE MKIII would it solve my problem OR would it mess ERRYTHANG up bcuz tha directories might change?
-
Maschine Mk2
Hello, I traded a friend an old piece of mine for his Mk2. I tried to register product and serial is taken. I'd like to get it registered to me. I'm the 3rd owner and don't know first owner/no point of contact. How do I get the hardware registered to me so I can get the software to unlock library and play around? I also…