Mapping Traktor

Recent discussions

Reset the step sequencer to the first beat/step on S8
Hello i finally got my hands on a S8. And i love it. Especially using the step sequencer on pro 3. But how do i reset the sequence to start from the first step again? To the first beat. While iam jamming along this would be good to know. so i dont have to stop exatly at the first step and then start the sequence again, so…
Microphone via the Aux Channel but with extra gain? + Aux volume mapping
Hello There are two methods to add a microphone on my S4 mk3. https://support.native-instruments.com/hc/en-us/articles/209590869-How-to-Use-a-Microphone-with-the-TRAKTOR-KONTROL-S4 Via live input deck, which takes the whole deck, or via Aux. When I do it via aux, is there a way to add a bit of gain to it? Otherwise it's a…
Z2 mapping master volume and output monitor
I just got my hands on a Z2. I've read in the manual that the output Master and Booth is for adjusting the outs on the back panel. I also noticed that when turning these knobs, Traktor picks up a midi signal. So I tried mapping these knobs for master volume and booth for the internal mixing but the learn function does not…
QML: signal I/O
Dear community, Has anyone figured out how to consume and process arbitrary control data streams in QML? OSC, perhaps? I currently use workarounds such as HTTP and global midi I/O, but this comes with limitations, is unnecessary complicated and does not allow for appropriate utility of adapters. If there is anyone out…
Mapping FX select buttons
Hello, I am looking into getting a Kontrol S3 + X1 to control FX units. My question is whether its possible to map out theese buttons for all four decks separately (eg. you press button and FX unit 1 turns on/off on deck A, you press another button and unit 2 turns on/off on deck D). I have been looking for the option in…
Kontrol S2MK3, hotcue pads order
After using the S4 for more than a decade, It's extremely annoying for me to have the hotcue order switched compared to the older models. Is there any way to reverse this from within Traktor (or perhaps the Controller Editor) without making a custom map? (consider this a feature request if the answer is no) If there is no…
"Load, Loop, and Play" command doesn't switch the Deck Flavor
Configure any Deck as a Remix Deck. Use "Load, Loop and Play" command to load a Track into a remix deck. (Add In --> Track Deck --> Load, Loop, and Play) This command doesn't seem to switch the Deck Flavor to a Track Deck like the "Load Selected" command does. Not a big deal as it can be fixed in the mapping but something…
Jog Wheels Mapping
Hi all I full map my DDJ REV 1 on Traktor Pro 3, but the only thing that I don't know is how map the jog wheels for slow down and increase the track speed and for scratching. Thanks
Remapping Deck Assign buttons
Both of the deck assign (DECK C and DECK D) buttons on my Kontrol S4 have become unreliable, often getting stuck in the depressed position. I would therefore like to map these functions (Deck A -> C and Deck B -> D, and vice versa) to another pair of buttons (most likely either the Flux or 3rd FX button on each deck). I…
Easy Swap Midi functions?
Hi. 1st time posting. I have a suggestion. I feel a way to easily swap the function of a button/knob/etc. For example I have an endless encoder set to select loop length with th appropriate out settings for led feedback, it would be nice to change that to control the low band of my eq without starting the entire map…
Custom FX mapping not working in Traktor 3.6.1
It has worked for years, since Traktor 2, so my questions are: 1) Is there any way to get to it work? 2) Is there any hope that whatever broke it between 3.5.3 and 3.6.1 will be remedied in a later update? The mapping is based on Tekken’s Kontrol F1 Ultimate Mapping v3.4, where I changed a bunch of the FX paramaters and…
Kontrol S2 MK3 Effects to Sample Pads Mapping
Hello I recently got me the S2 MK3 to match Traktor 3 Pro software. I now have the following in mind: Since I wouldn't really use samples, I would want to put effects on the sample pads. So (when sample mode is activated) the effect should be activated by pressing the pad and deactivated again when you release it. However,…
Adding Different Filters to FX1 / FX2 Knobs for Kontrol S2 on Traktor Pro 3
So I want to have different filters for each of the 3 knobs on the FX1 and FX2. Similar to https://www.youtube.com/watch?v=tBVVAKCqC_M For example.... have Knob 1 be Reverb, Knob 2 be Beatmasher, Knob 3 be Time Gater
led mapping inferno
hello ! I'm trying to map my new launchcontrol XL. I mapped a lot on it and everything works as intended, light and everything. I want to map on 4 buttons (track focus as they called them) "loopsize+select" function as loop 1>loop 2>loop 4>loop 8. that works but there is no light :) so I'm trying to map some "out" mapping.…
Help mapping Denon DN-HC4500 (Receive text on LED display)
hi I am playing with the mapping of the Denon - DN-HC4500 trying to find out which are the messages that send text to the screen, I have tried to map that function many times and I have never succeeded. Could someone tell me what is the part of the .tsi that sends those messages to the controller? It is for educational…
Custom mapping "Kontrol S4MK3 Ninja" in not working correctly in Traktor Pro 3.6
Hi, Custom mapping "Kontrol S4MK3 Ninja" is not working correctly in Traktor Pro 3.6. When pressing Shift + Sample you have to press the pads two times before the effect is on. In Traktor Pro version 3.4.2.256 the mapping is working as it should be by pressing pads one time. Best regards Mikael
I did a thing with Pattern Player (sound Selector knob)
No knob mappings? No problem.
Pioneer REV7 Midi mapping
Hey Has anyone created a Rev 7 Midi mapping? I've been trying but, well I suck hahah.
How to switch effects fx1 and fx2 with buttons on s4 mk2?
Hello, I would like to know how I can do to be able to change the effects FX1 and FX2 with the buttons of the S4 Mk3 without having to do it with the pc in the program. I have three effects chosen from a drop-down list in FX1, and another three in FX2 as well, but I would like to be able to change each of the effects…
Pioneer S7 Mapping
So as a fun little side project I thought I’d play around with building an S7 mapping for Traktor. Most of the mapping is pretty straightforward, but I’m having some difficulty getting the pad mode LEDs to illuminate. Has anyone gotten the pad mode LEDs on a Pioneer mixer to light up when using Traktor? I’ve followed the…