-
Map Stems to Z2?
Has anyone been able to or is it even possible to map any of the pads or effects on the Z2 to the individual stems? I realize this is an old mixer but I love it and refuse to move off control vinyl with 1200s. If not who what is the best setup for a turntablist that wants to easily play with stems on a pad while performing?
-
Mapping an old controller (DJ-Tech I-Mix Reload MK1) on Traktor.
Hello, I'm an old DJ (48 years old) who started on CD (25 years ago...) , then on controller (but at the time, I didn't really like it) and today on Vinyl (and I like it... ). As I had bought Traktor 2 at the time, I benefited today from the current discount to upgrade Traktor 2 to Traktor 3 after I was given a DJ-Tech…
-
Mapping
Hey there I have some interest in figuring out mapping. I'm not exactly sure how to go about it. I had some mappings for my dicers that were the absolute best. Since dicers are no longer supported the mappings no longer work with traktor 3. How would one open the mapping file to see what it's doing or can someone give me a…
-
Key / Mapping
Hallo zusammen, Ich habe bisher einen S8 genutzt und bin eine Zeit bei Denon hängen geblieben. Möchte wieder zurück wechseln. Kann ich auf den neuen Kontrollern (S4 MK3) immer noch mapping für die Tastenzuweisung durchführen? Speziell kann ich einen Drehregler für die Tonhöhe mappen? Danke und beste Grüße
-
Mapping Tsi To Rane
Im Lookin To Map My Rane Seventy Mixer With My Rane Twelves Mk11s for The Traktor Software I Hate Manual Mapping any Suggestions
-
Tsi bug? 2 inputs and outputs are present when plug in 2 f1
hi team, I’ve tried all combinations with all senerios and mappings. I have a Traktor s4mk3 and 2 f1. When I plug in 2 f1 I get this strange bug where 2 inputs and outputs are present. Every time I start Traktor I have to physically go into controller manger and change to bottom input and output or it doesn’t work. Driving…
-
DDJ-SZ and SX2 family - Traktor mapping
This is a 2021 maintained mapping for the DDJ-SZ / SX2 family of controllers. 7K downloads so far. It has versions with and without BOME. https://maps.djtechtools.com/mappings/9222
-
Need Help with Kontrol F1 and X1 Setup for Live Tekk Sets (Step Sequencer)
Hello dear community, I have a question about my setup and I hope you can help me. I use two Kontrol F1 controllers and one Kontrol X1 to play live Tekk sets. However, I'm facing some challenges and I need your assistance. Let's start with the physical arrangement of the controllers: From left to right, I have the F1, then…
-
TSI import
Are there any other ways to import TSI data into Traktor besides clicking on Import in Control Manager?
-
I NEED MAPPING FOR CONTROLLER NUMARK N4....THIS CONTROLLER HAVE A 10 YAERS OLD...
SORRY FOR WRITE IN SPANISH, I NEED MAPPIN FOR CONTROLLER NUMARK N4....IS ABOUT 10 YEARS OLD....AND IN INTERNET JUST FINDED MAPPING FOR TRAKTOR PRO2, THANKS REGARDS
-
HOLAAA, ACABO DE INSTALAR TRAKTOR PRO3, TENGO UNA NUMARK N4 VIEJECITA....COMO 10 AÑOS....EL MAPPING?
HI GAYS, I NEED A MAPPING FOR TRAKTOR PRO3, MY CONTROLLER IS OWN....IT,S A NUMARK N4, ABOUT 10 YEARS OLD...IN INTERNET JUST FINDED MAPPING FOR A TRAKTOR PRO 2,PLEASE CAN HELP ME IF THER IS SOME MAPPING FOR TRAKTOR PRO3, THANKS REGARDS
-
MIDI Mapping
Does anyone know if there will be a MIDI mapping update so that if might be more like Ableton where it is visual based so you can click on the function and assign buttons and conditions...?
-
I need all Midi message values for the VU meter which will be send by Traktor
Hi NI support and all other members, i need all Midi message values for the VU meter which will be send out by Traktor to map these correctly to my hardware controller. Traktor is using the midi cc command: midi channel, midi purpose, midi value, example: 0x01, cc 121, value (0-127), I believe that every led has a range of…
-
RE-Mapping controls on the Traktor S-8
Is it possible to re-map the controls on the Traktor S-8 in the same manner that as the S-4? Specifically, I would like to re-map one of the FX knobs to Master Tempo. Some of my DJ routines require full 1 bpm stepping with one hand. The built in Tempo knob does .1 stepping which take much too long for my needs. It requires…
-
Is it possible to re-map the SHIFT control on an X1 mk2 ?
Is it possible to re-map the SHIFT control on an X1 mk2 ? I'm presuming you have to go to MIDI mode, which is a pain as its too slow and too many button combos when you're in the heat of the moment.
-
DDJ ERGO limited-mapping
Hello friends, we have a ddj ergo device and we saw that it works with tractor pro licensed. I want to ask you, is this device approved only with traktor pro or can it be used with rekordbox? apparently from old production devices. So I couldn't find much information on the internet. If it is not compatible with rekordbox,…
-
Tracktor x1 mk1 fx mapping needed - I m a bit lost
Hello there people, i just got as a present a traktor x1 mk1 and one of my friends share his traktor pro 3 license with me, i want to use as fx pannel and being able to play some accapellas and stems, because my set up is currently a DJM 850 and 2 Cdj 2000 - so my mixing and main track controls are already covered. The…
-
i managed to get the S4mk1 controller working on a M1mac (midi mode only)
with a windowsPC or latop you can basically network your S4mk1 to send midi signal over to your m1 using RTPmidi on the PC side and utilising the midi network setup on the M1. dont know if this is practical or not... but it is possible to still utilise the S4mk1 controller in midi mode to operate traktor pro 3 on the M1 my…
-
Could S2MK3 be used as an MIDI input
Dear friends, I am a green hand of the sound engine a stupid question about my tractor, could my s2mk3 been used as a midi input in sound program software (Max/MSP), I try to connect it by using my USB line, however, it can not be detected. Like the picture shown.
-
Traktor kontrol F1 mapping
Hello, I need some information before purchasing the traktor 3.0 upgrade. I'm Using a mapping for the traktor kontrol F1 (precisely the tekken's kontrol Ultimate v3.4), I wanted to know if it is also compatible with the new version of the program. Thanks to everyone and have a good day