Xone K2 Modifier/Browser Mapping BUGS

DZZ

hi everyone,

so i found an existing mapping that has desired functionality for browsing, selecting, previewing. i tried lifting it from that mapping to put into my mapping but there are several bugs.

the original working mapping is:

• based on latches,
• to enter browsing mode, the 'exit setup' button is pressed, it lights up in green
• once in browsing mode, the knob immediately to the left selects up and down
• pressing said knob will load and play the selected track in the preview player
• pressing knob again will stop the preview player
• when exiting the browsing mode, the same knob will control the mix volume

i loaded this mapping and extracted what i thought was relevant and here is the behavior i am seeing:

• my mapping is not based on latches and latch mode is disabled
• 🚫 i enter browsing mode, but button does not light up in green
• 🚫 in browsing mode, the knob does not work in selecting up or down
• 🚫 pressing the knob does load the selected track to the preview player but the track does NOT play
• pressing knob again will stop the preview player
• the same knob will control the mix volume, but does NOT work for selecting in browsing mode

Here is a comparison of the working mapping vs mine. there are several assignments to modifier #1 which is very confusing. i'm not sure if this has to do with latches or not, but i am kind of lost and not sure what is missing.

the original working mapping can be DL here:

https://mega.nz/#!tF80gYgC!gOqEFF7wuxGBXVtJTXWYbo1jhTvkjACe5lH-zu3N0fk

here is a video demonstrating it clearly (its in spanish but there are subtitles)

https://www.youtube.com/watch?v=7fxS20ojvWE

Thanks again!

Sûlherokhh

https://community.native-instruments.com/discussion/26608/xone-k2-modifier-browser-mapping-bugs

Make sure you catch the right notes/CC both for input and output. Look at the manual (page 17+18).

For input (without latched layers), the values you need are all the number corresponding to the colour RED. For output, all three colour values are available.

https://www.manualslib.com/manual/778554/Allen-And-Heath-Xone-K2.html?page=17#manual

DZZ

https://community.native-instruments.com/discussion/comment/133013#Comment_133013

thanks, though i believe that the issue is not so much with right notes.

the working mapping works as expected.

so i simply copied it and transferred to my mapping.

the notes as such ad correct since they worked originally.

this would indicate something else is going on. 🙏

DZZ

that said i did indeed confirm the notes are correct.

i suspect that it has something to do with the modifiers.

i guess i can try eliminating each line item in the working mapping to try and isolate further.

Stevan

Could this be just a Send Monitor State issue? K2 is having issues with refreshing the controller output so it needs to be forced to refresh the LED each time modifier value is changed.

If that is so, just map the monitor state to your browser encoder. (or any other modifier button for that matter)

DZZ

https://community.native-instruments.com/discussion/comment/133071#Comment_133071

hmmm, the original mapping does not have or include any "Send Monitor State" assignments, so I'm thinking that's not it.

Stevan

https://community.native-instruments.com/discussion/comment/133155#Comment_133155

Upload your custom mapping then to investigate it.

DZZ

ok, so i resolved this by slowly deleting every line in the working mapping that was unrelated to the function. once i isolated only the assignments that produced the function, i double checked each and every setting and it turns out the modifier conditions were the culprit!

Ramonihm

I got the same problem. It could be better if DZZ explains with details (add ins and modificators) the solution of the issue