Mapping for Kontrol S3

deejayos · 2025-05-26T16:11:09+00:00

There was an error rendering this rich post.

ich habe bisher einen s2 mk3 benutzt… bei dem habe ich die cue-taste so gemappt, dass bei einem druck der aktuell im browserfenster song in das deck geladen wird und er einmal aufleuchtet (also in & out, usw…)

jetzt mein problem: ich habe nun einen s3 und würde das hier auch gerne so einrichten, aber wenn ich die taste über die learn-funktion auswähle ist es immer "die eine cue-taste" auch wenn ich über die buttons das deck wechsle…

also lädt der track in beide decks der linken (oder rechten) seite… wie kann ich das mappen, dass er das jeweils nur in das anzusteuernde (a→c oder b→d) deck lädt? ich komme immer nur auf die eine cue-taste….

Find more posts tagged with

Traktor Pro 3

Comments

deejayos

google translator:

I've been using an S2 MK3 so far... I mapped the cue button so that when I press it, the song currently in the browser window is loaded onto the deck and it lights up once (i.e., in & out, etc.).

Now my problem: I now have an S3 and would like to set it up the same way here, but when I select the button using the learn function, it's always "the one cue button," even if I change decks using the buttons...

So the track loads onto both decks on the left (or right) side... How can I map it so that it only loads onto the deck I want to control (a→c or b→d)? I always only get to the one cue button...

VityaT

Post edit

Didn't understand question. My bad

Sûlherokhh

https://community.native-instruments.com/discussion/comment/228156#Comment_228156

You need to use modifiers that trigger when pressing or holding the deck and shift buttons ('override' option must be unchecked). Those modifier value need to be restricting the functions you want to map to your decks as 'modifier conditions'.

I did this for the s4mk3. Here is a link to some qml mods, but importantly i also provided a TSI to be used (at the end of the post). I have called this a modifer skeleton, as it provides the modifier structure that you can add functions to.

Read the explanation next to the download, then download the s4 TSI file, open it and read it. Then you will know what you will need to add to the S3 TSI file.

LINK

deejayos

https://community.native-instruments.com/discussion/comment/228207#Comment_228207

Can't you be more specific?

VityaT

You need to assign a modifier state to each deck
For exmple
For deck С button you need:

Add In - Modifier #1

Modifier Conditions M1=0

Type of Controller - Button

Interaction Mode - Direct

Set to value - 1

For deck A button you need:
Add In - Modifier #1

Modifier Conditions M1=1

Type of Controller - Button

Interaction Mode - Direct

Set to value - 0

After that all commands you want for deck A must be with Modifier Conditions M1=0 and for deck C with Modifier Conditions M1=1

For deck B and D you should use another modifier - M2 for example

deejayos

okay….thx…i will try it

Sûlherokhh

https://community.native-instruments.com/discussion/comment/228265#Comment_228265

Okay, i copied the section from my post that describes what values to use:

Excerpt:

"The mapping includes a modifier skeleton for you own mapping use that recognizes SHIFT and DECK layers in the following manner:

Modifer#1 = 0: Deck A
Modifer#1 = 1: Deck A (shift layer)
Modifer#1 = 4: Deck C
Modifer#1 = 5: Deck C (shift layer)
Modifer#2 = 0: DeckB
Modifer#2 = 1: Deck B (shift layer)
Modifer#2 = 4: Deck D
Modifer#2 = 5: Deck D (shift layer)"

File link:

Kontrol S4MK3 Factory.Edit ModifierLayerSkeleton-03.tsi

It looks like this:

Transfer all commands to the S3 mapping and assign the appropriate S3 buttons to the lines. Remember to check or uncheck the correct checkboxes for each assignment (some have 'override factory mapping' or 'inverted' either checked or unchecked).

Edit: Ha, i discovered i already did a transfer, with extra gain knob calibration, for the S3. Here it is:

S3-Modifier-Layer-Skeleton.tsi

deejayos

The "original mapping" for the S3 has a switch for the decks - the cue button therefore functions for decks A/C & B/D by default - is it not possible to set it up so that when switching via the deck selection the cue button also switches?

Sûlherokhh

https://community.native-instruments.com/discussion/comment/228953#Comment_228953

Not out of the box, you have to replicate the states by using modifiers. The TSI i provided does that.

Whatever function you assign to the CUE button, just add the modifier condition 'M1 = 0' for deck A. Duplicate the assignment, make it deck C and change the modifier condition to 'M1 = 4'.

See here (again):

Modifer#1 = 0: Deck A
Modifer#1 = 1: Deck A (shift layer)
Modifer#1 = 4: Deck C
Modifer#1 = 5: Deck C (shift layer)
Modifer#2 = 0: DeckB
Modifer#2 = 1: Deck B (shift layer)
Modifer#2 = 4: Deck D
Modifer#2 = 5: Deck D (shift layer)

If you don't understand what i am talking about, i can upload another sample TSI with a deck function that uses the modifier skeleton to register deck switches and shift state.

deejayos

https://community.native-instruments.com/discussion/comment/228953#Comment_228953

But i don't want tor work with the shift button?!

Sûlherokhh

https://community.native-instruments.com/discussion/comment/233157#Comment_233157

Then just delete the SHIFT button assignments from the list. Values 0 (top deck) and 4 (bottom deck) will remain functional in this case, even with SHIFT held down.

Quick links

Unanswered questions