S4MK3 & S3: Performance MOD (qml coding)

1…2425262729

Comments

  • pixel
    pixel Member Posts: 191 Advisor

    cool, I'll send you the new mod this evening so you can try it out😀

  • pixel
    pixel Member Posts: 191 Advisor

    @tokamak:

    I sent you the mod.😀
    have fun testing😁

  • tokamak
    tokamak Member Posts: 8 Member

    Will test tonight!

  • Sûlherokhh
    Sûlherokhh Member, Traktor Mapping Mod Posts: 2,627 mod

    After two weeks of testing i updated the front page…

    Update for TP 4.1.0 - S4MK3-PerformanceMod V.6

    New Stem Deck Features:

    • Pads 1-4 LEDs (Mute Toggles): LEDs will now blink when MUTE is activated so you don't have to rely on the LED brightness to know if MUTE is active or not.

    New Track/Stem Deck Hotcue Features:

    • PadMode.Hotcue (Hold) + Pads 3+4: Jump to previous/next Hotcue
    • PadMode.Hotcue (Hold) + Pads 5-8: Remap Hotcue type (Load, Fade-In/Out, Hotcue
    • SHIFT(Hold) + PadMode.Hotcue (Tap) + Hotcue: Remap Hotcue to new number

    Happy spinning! 🦋

  • pixel
    pixel Member Posts: 191 Advisor

    very cool😎

    As soon as I release the new S3Mod, I will integrate all new features of Sûlherokhh (S4MK3-PerformanceMod V.6) into the S3 mod. I'll start this over the weekend, but won't release the update until St. Nicholas Day.😅

    So clean the S3🤣

  • tokamak
    tokamak Member Posts: 8 Member
    edited November 13

    is there any way to capture loops/samples on the fly on an sampledeck, simular to the F1?

    I didend found anything for S3 so far.


  • Sûlherokhh
    Sûlherokhh Member, Traktor Mapping Mod Posts: 2,627 mod
    https://community.native-instruments.com/discussion/comment/190615#Comment_190615

    Yes, by pressing a sample button that is currently set to a cell of the remix slot that is empty. Sample size will equal the deck Loop size of the capture source. But you can't adjust the capture source currently.

    Thank you for asking me about it. It didn't even occur to me since my main setup can easily do this and i use my S4 only at home. My next update will incorporate a capture source selector for the remix decks.

    Note: just in case you don't know yet; You can switch between all sixteen cells of each slot by holding down the white slot button (pads 5-8) and turning the browse encoder.

  • pixel
    pixel Member Posts: 191 Advisor
    edited November 19

    For anyone who doesn't know what the LFO-Reset is, I created a video with audio :)

    lfo-reset.zip

    and Browser-Features

    Browser-Features.zip

    Stem-Separation Control

    Stem-Separation Control.zip

    FX

    • Assign the FX devices to the respective deck
    • Activation of FX mode
    • Control of the selection boxes for the FX device

    In the video the old button Color assignment is shown, please note readme.txt

    FX_Control.zip

    FX Snapshot

    In the video the old button assignment is shown, please note readme.txt

    FX Snapshot.zip

    FX Rec mode, Play mode

    FX_PLAY_REC.zip
    FX_Play_Rec_2.zip

    FX PatternPlayer

    PatternPlayer1.zip
    PatternPlayer2.zip
    PatternPlayer Kit-Select.zip

    If I make another video tomorrow, it will go in here

  • tokamak
    tokamak Member Posts: 8 Member
    https://community.native-instruments.com/discussion/comment/190619#Comment_190619

    ok, thanks.
    I've been thinking about how to implement this the last days.
    I think the easiest way would be really similar to the F1.

    Shift+Samples on the active sample Deck to activate capture mode
    PAD 1-4 blinking, to select source deck to sample from.
    Alternatively shift+ turn loop encoder with blinking pads to visible wich deck is selected.
    once deck is selected…

    • Turn loop encoder for the size of the sample,
    • Turn Move encoder to move the loop.
    • Trigger loop encoder to activate loop.
    • Trigger the pad you want to assign the loop to the Pad.
    • shift+Pad to delete assigned sample
    • tap samples again to leave the Capure mode.

    Also nice to have on sample deck
    Shift+loop encoder page selector mayby rowwise to use more than 4 samples per deck
    Hold pad + turn move encoder for adjusting volumen of the sample
    Hold pad + loop encoder for filter for the sample on this pad / press encoder on/off Filter

  • Sûlherokhh
    Sûlherokhh Member, Traktor Mapping Mod Posts: 2,627 mod
    https://community.native-instruments.com/discussion/comment/190820#Comment_190820

    I thought just holding down 'SAMPLES' will activate capture source control, using one of the encoders, probably browse encoder, with a screen pop-up field that displays the currently selected source. The screen bit will probably take the longest, so i may do the update in two steps.

    As much as i love the F1, some of the menu design is a bit cumbersome to employ.

  • tokamak
    tokamak Member Posts: 8 Member

    ok, I can see that I'm stuck in the old possibilities of midi mappings and I'm not always aware that qml can do much more than MIDI mappings 🤣
    Of course that would be more elegant.
    By screen pop-up you probably mean the display on the S4?
    I can only talk about S3!

  • Sûlherokhh
    Sûlherokhh Member, Traktor Mapping Mod Posts: 2,627 mod

    Screen feedback is for S4, the code will work on both although i leave it to pixel to place the code into the relevant S3 files.

  • pixel
    pixel Member Posts: 191 Advisor

    An update will be released on December 6th^^

  • DJ ALX
    DJ ALX Member Posts: 25 Member
    https://community.native-instruments.com/discussion/comment/187975#Comment_187975

    I did both to get the PAD led to turn off completely. Both worked but when I would toggle from SAMPLES to HOTCUES and back to SAMPLES, the turned off leds would be blinking again. No worries. I just have them blink at 100msec intervals. I will keep it like this for now and maybe we can address it in the future.

    Another thing Is when I hold SHIFT and pads 5-8 to turn on/off the EFX sends the pad lights to bright orange but only for as long as Im pressing it. The FX send is turned on but the pad goes back to dark orange again.
    When I toggle from SAMPLES to HOTCUES and back to SAMPLES and press SHIFT then the FX that are ON appear right orange like they should. Any idea where to look?

    Maybe @pixel has solved this?

  • tokamak
    tokamak Member Posts: 8 Member

    Very Nice!!

    thanks for the good Work again!

Back To Top

Categories