S4MK3 & S3: Performance MOD (qml coding)

pixel · November 12

cool, I'll send you the new mod this evening so you can try it out😀

pixel · November 12

@tokamak:

I sent you the mod.😀
have fun testing😁

tokamak · November 12

Will test tonight!

Sûlherokhh · November 12

After two weeks of testing i updated the front page…

Update for TP 4.1.0 - S4MK3-PerformanceMod V.6

New Stem Deck Features:

Pads 1-4 LEDs (Mute Toggles): LEDs will now blink when MUTE is activated so you don't have to rely on the LED brightness to know if MUTE is active or not.

New Track/Stem Deck Hotcue Features:

PadMode.Hotcue (Hold) + Pads 3+4: Jump to previous/next Hotcue
PadMode.Hotcue (Hold) + Pads 5-8: Remap Hotcue type (Load, Fade-In/Out, Hotcue
SHIFT(Hold) + PadMode.Hotcue (Tap) + Hotcue: Remap Hotcue to new number

Happy spinning! 🦋

pixel · November 12

very cool😎

As soon as I release the new S3Mod, I will integrate all new features of Sûlherokhh (S4MK3-PerformanceMod V.6) into the S3 mod. I'll start this over the weekend, but won't release the update until St. Nicholas Day.😅

So clean the S3🤣

tokamak · November 13

is there any way to capture loops/samples on the fly on an sampledeck, simular to the F1?

I didend found anything for S3 so far.

Sûlherokhh · November 13

https://community.native-instruments.com/discussion/comment/190615#Comment_190615

Yes, by pressing a sample button that is currently set to a cell of the remix slot that is empty. Sample size will equal the deck Loop size of the capture source. But you can't adjust the capture source currently.

Thank you for asking me about it. It didn't even occur to me since my main setup can easily do this and i use my S4 only at home. My next update will incorporate a capture source selector for the remix decks.

Note: just in case you don't know yet; You can switch between all sixteen cells of each slot by holding down the white slot button (pads 5-8) and turning the browse encoder.

pixel · November 13

For anyone who doesn't know what the LFO-Reset is, I created a video with audio :)

lfo-reset.zip

and Browser-Features

Browser-Features.zip

Stem-Separation Control

Stem-Separation Control.zip

FX

Assign the FX devices to the respective deck
Activation of FX mode
Control of the selection boxes for the FX device

In the video the old button Color assignment is shown, please note readme.txt

FX_Control.zip

FX Snapshot

In the video the old button assignment is shown, please note readme.txt

FX Snapshot.zip

FX Rec mode, Play mode

FX PatternPlayer

PatternPlayer Kit-Select.zip

If I make another video tomorrow, it will go in here

tokamak · November 13

https://community.native-instruments.com/discussion/comment/190619#Comment_190619

ok, thanks.
I've been thinking about how to implement this the last days.
I think the easiest way would be really similar to the F1.

Shift+Samples on the active sample Deck to activate capture mode
PAD 1-4 blinking, to select source deck to sample from.
Alternatively shift+ turn loop encoder with blinking pads to visible wich deck is selected.
once deck is selected…

Turn loop encoder for the size of the sample,
Turn Move encoder to move the loop.
Trigger loop encoder to activate loop.
Trigger the pad you want to assign the loop to the Pad.
shift+Pad to delete assigned sample
tap samples again to leave the Capure mode.

Also nice to have on sample deck
Shift+loop encoder page selector mayby rowwise to use more than 4 samples per deck
Hold pad + turn move encoder for adjusting volumen of the sample
Hold pad + loop encoder for filter for the sample on this pad / press encoder on/off Filter

Sûlherokhh · November 13

https://community.native-instruments.com/discussion/comment/190820#Comment_190820

I thought just holding down 'SAMPLES' will activate capture source control, using one of the encoders, probably browse encoder, with a screen pop-up field that displays the currently selected source. The screen bit will probably take the longest, so i may do the update in two steps.

As much as i love the F1, some of the menu design is a bit cumbersome to employ.

tokamak · November 13

ok, I can see that I'm stuck in the old possibilities of midi mappings and I'm not always aware that qml can do much more than MIDI mappings 🤣
Of course that would be more elegant.
By screen pop-up you probably mean the display on the S4?
I can only talk about S3!

Sûlherokhh · November 13

Screen feedback is for S4, the code will work on both although i leave it to pixel to place the code into the relevant S3 files.

pixel · November 13

An update will be released on December 6th^^

DJ ALX · November 13

https://community.native-instruments.com/discussion/comment/187975#Comment_187975

I did both to get the PAD led to turn off completely. Both worked but when I would toggle from SAMPLES to HOTCUES and back to SAMPLES, the turned off leds would be blinking again. No worries. I just have them blink at 100msec intervals. I will keep it like this for now and maybe we can address it in the future.

Another thing Is when I hold SHIFT and pads 5-8 to turn on/off the EFX sends the pad lights to bright orange but only for as long as Im pressing it. The FX send is turned on but the pad goes back to dark orange again.
When I toggle from SAMPLES to HOTCUES and back to SAMPLES and press SHIFT then the FX that are ON appear right orange like they should. Any idea where to look?

Maybe @pixel has solved this?

tokamak · November 13

Very Nice!!

thanks for the good Work again!

S4MK3 & S3: Performance MOD (qml coding)

Comments

Update for TP 4.1.0 - S4MK3-PerformanceMod V.6

Categories