S61 MK3 driver/firmware

flashrebob
flashrebob Member Posts: 8 Newcomer
edited October 22 in Komplete Kontrol

I just received my S61 MK3. I cannot update the firmware because Windows 11 does not have the driver. I have all of the Windows Updates, tried to update the driver by disabling the driver verification, uninstalled and reinstalled all of the pertinent NI software, etc.
I am at a dead end. I see no way provide a support ticket.

Tagged:

Comments

  • flashrebob
    flashrebob Member Posts: 8 Newcomer

    PS. Tried all of these.
    https://support.native-instruments.com/hc/en-us/articles/14229160390045-Kontrol-S-Series-MK3-Troubleshooting-Firmware-Update-Issues
    https://support.native-instruments.com/hc/en-us/articles/14229160390045-Kontrol-S-Series-MK3-Troubleshooting-Firmware-Update-Issues
    https://vi-control.net/community/threads/i-am-desperate-from-my-new-native-instruments-kontrol-s88-mk3.144847/

  • Matthew_NI
    Matthew_NI Product Team Posts: 1,431 mod

    @Jeremy_NI can help you out

  • flashrebob
    flashrebob Member Posts: 8 Newcomer

    Okay. How so?

  • Jeremy_NI
    Jeremy_NI Customer Care Posts: 12,716 mod
    edited July 31

    Well, if you already tried these steps, I'll get in touch by email.

    Just a question though, as these issues are mostly caused by the USB C connection, have you tried a USB C hub as mentioned in the KB article here? Kontrol S-Serie MK3: Troubleshooting Firmware Update Issues

    In the future if you need to contact support you have to go on the website, go to the SUPPORT section. I've made a gif for users who struggle to contact us:

    how to use support main.gif

  • flashrebob
    flashrebob Member Posts: 8 Newcomer

    Jeremy,

    Now that I have the correct driver but now when updating it gets stuck on "Update successful, waiting for reboot." Device appears to not be recognized again.  Starting over and over, and also getting notices that this waiting is timing out the firmware update and I have to say keep waiting over and over again.
    Now I am going to leave it on over night.

    Trying on a 2nd windows computer and getting the same thing. It is sitting on the last firmware update "waiting for reboot."

    Very frustrating…. Unit I got was on firmware 0.0.1

  • flashrebob
    flashrebob Member Posts: 8 Newcomer

    I have tried all of this.

    Tried 3 different ways to power the unit. Says low power with everything I have tried.

    New USB cables. Both with and without a USB-A to USB-C adapter.

    New powered USB 3.0 hub with power for the panel.

    Used 3 different USB charging stations.

    Saw somewhere turning off and on 5 times. This works for the unit to show up in device manager. When I try to update the driver there are no drivers (S61 MK) in the Native Instruments list.
    Firmware EXE does not find the unit either.

    Tried going into safe mode and turning off driver verification.

    Tried disabling Windows Defender.
    Rinse and repeat all of these steps based on each change.

  • JacekJ
    JacekJ Member Posts: 3 Newcomer

    Best way is to power keyboard with USBC power with two way USBC cable. I have no problem using one cable for data and power from my laptop or desktop PC. I am afraid that USB-A is the reason.

  • Jeremy_NI
    Jeremy_NI Customer Care Posts: 12,716 mod
    https://community.native-instruments.com/discussion/comment/169581#Comment_169581

    I'm waiting for your reply by email. It's better to continue the conversation there so I can forward to a specialist. Please check your inbox and add any info you see necessary. Thanks.

  • flashrebob
    flashrebob Member Posts: 8 Newcomer

    I am not sure how using a USB-A to USB-C 3.0 cable would affect anything. My computer does not have any USB-C direct connections.

    Jeremy, I will look in the Support thread.

  • Matthew_NI
    Matthew_NI Product Team Posts: 1,431 mod
    https://community.native-instruments.com/discussion/comment/169807#Comment_169807

    USB-A does not provide enough power to reliably power the Kontrol S MK3.

    However, if the hub itself was powered, prior to going into a USB-A port, that would not explain this.

    Perhaps your DFU driver is broken? Have you tried this step? It worked for another user this evening who was having unexplained odd issues simply trying to update their KSMK3.

    https://support.native-instruments.com/hc/en-us/articles/16567321051805-How-Can-I-Update-the-Driver-and-Firmware-of-My-Kontrol-S88-MK3-on-Windows?

  • flashrebob
    flashrebob Member Posts: 8 Newcomer

    Even with a powered Hub when using USB-A you get the error for the USB-A power. I believe the issue is using USB-A to USB-C cabling. When I connected to my work laptop the panel come right up. I have to order a USB-C card for my computer and will reply again after that.

  • flashrebob
    flashrebob Member Posts: 8 Newcomer

    The USB-C card I added to my computer did the trick. Booted right up and I could follow thru with the rest of the process.

    Using a powered Hub did not work.

This discussion has been closed.
Back To Top

Categories