Questions programming with Reaktor Blocks / Prime

Hello, I have a few beginner questions. I purchased Reaktor Blocks Prime and would like to implement the following things, for which I have not been able to find any tutorials so far. I hope this is possible in patching with the Reaktor 6 player.

How to assign parameters to pitch bend and modulation wheel.
How to programm 8 macro controls for use with Komplete Kontrol software.
Integrating the Scope Utility.

I'm grateful for any tips :I

Find more posts tagged with

Comments

PoorFellow

https://community.native-instruments.com/discussion/49716/questions-programming-with-reaktor-blocks-prime

How to assign parameters to pitch bend and modulation wheel

Did you try a Google search such as this ? Which immediately brings up a video such as this one !

Or if for blocks , then did you look in the manuals ? E.g. including section "11.9.10. Note In (INT)" in the Reaktor Blocks Manual

How to programm 8 macro controls for use with Komplete Kontrol software.

Did you try a Google search such as this ? Which immediately brings up a forum thread such as this one !

Integrating the Scope Utility

I am not exactly sure here what situation is and what it is that you want to do….

I'm grateful for any tips :I

Download and use all the manuals , please notice that some manuals for Reaktor 5 is still needed to cover some information not found in the Reaktor 6 manual range…

Also notice the Learning Resources page , not to mention the great amount of tutorials found on the internet… With respect to tutorials (often old) then also notice that if you have that then there should be a Legacy Library ZIP file in the Reaktor Factory Library directory containing some old stuff that you can otherwise not find/use.

DS99

Thank you very much for the information. Of course, I had already looked on Google and in the knowledge base, but couldn't find anything suitable. I also watched the learning videos, but they didn't cover this content.

PoorFellow

https://community.native-instruments.com/discussion/comment/254108#Comment_254108

Well , In general , from my own observations , then when it comes to getting help with Reaktor 6 (and other things for that matter) then the best thing is to make an exact use case/layout and then ask an exact question based on that. And in the case where there is any layout to save that other people can use to make a few quick changes to show you then perhaps save the layout and attach to your question.

Generalized diffuse questions is hard to answer and those asking indirectly sort of expect for other people to do a whole lot of work or write a novel to answer their question.

So my advice is to give an exact use example of something in Reaktor 6 when asking a question… Keep it as concise as possible…

DS99

That's a very good suggestion and comment. Thank you. Of course, you try to figure out what's possible yourself first, but the subject matter is quite complex :)

Attached two screenshots of my rack and the patch. I'm having problems switching to the Komplete Kontrol software – Macro Control assignments.

I programmed the first two macro knobs in my Reaktor patch for testing. Then I opened the rack in the Komplete Kontrol software to try to assign them to Macro Controls 1 and 2 of the first macro page and name them.

I can load the rack, but the Komplete Kontrol software also displays the Reaktor layer. Only the blocks of the rack should appear there. I therefore saved the rack as an ensemble and wanted to open it in the Komplete Kontrol software, but it is not recognized despite scanning the library and user library folder.

I have also noticed that the KK software automatically maps a number of parameters to the various pages of Macro Controls, see screenshot. There are a maximum of 16 pages, each with 8 macros to assign.

I would be happy if I knew how to remap und rename them to page 1 displaying the first 8 Macro Controls.

Moreover, how to assign my created macros 1 and 2 from the Reaktor patch in KK Software.

If I want to assign the 8 macros from my Reaktor patch, I probably have to create a second block with 4 knobs in the Reaktor rack, is that correct?

01 DWG FM I MONARK FLT MACRO 1-4.nksr.zip

PoorFellow

That's a very good suggestion and comment. Thank you.

Glad if that were helpful 🙂

I programmed the first two macro knobs in my Reaktor patch for testing.

I am rather much a novice myself with respect to Reaktor , but would I not also have to have your "Reaktor patch" layout save for testing and trying the "01-dwg-fm-i-monark-flt-macro-1-4-nksr" that you uploaded ?

DS99

I've now figured out how the mapping works. It's all done via the KK software, see screenshot. If you want to change individual macro controls, you can do so via the respective drop-down menu. Then save the rack again in the KK software.

What I still don't understand: The Komplete Kontrol software also displays the Reaktor layer, i.e. below the blocks. This layer shouldn't be visible. Why is that?

Quick links

Unanswered questions