How Can I connect X1 To Traktor X1 Mk1

Medhat Salem
Medhat Salem Member Posts: 12 Member
in Traktor Software & Hardware

Can Anybody Tell me Why X1 Mk1 Doesn't recognized By Traktor Pro 3 ? Its Flashing light Once i connect It To The laptop But It Then Doesn't Give anything after I Open traktor pro3 ! Thanks For The Advice

Tagged:
«1

Answers

  • Uwe303
    Uwe303 Moderator Posts: 4,736 mod

    Hello,

    have you tried to open the preferences and add this controller under the mappings page? Have you installed the driver from the drivers and downloads page?

  • Medhat Salem
    Medhat Salem Member Posts: 12 Member

    UWE - Thanks For Reply , I already Downloaded The driver , But I don't know How to Adjust The X1 from The mapping - Can You Give Steps for the mapping adjustments - THANK YOU

  • Medhat Salem
    Medhat Salem Member Posts: 12 Member
    Picture 1.JPG Picture 2.JPG

    in Picture 1 only Two Buttons are Lighted (SHIFT and HOTCUE) when I connect The X1 to Traktor Pro 3

    and in Picture 2 The X1 Didn't Light The FX1 and FX2 Buttons and All the effects buttons are not working (Wet / Dry - Delay - Reverb - Filter) but all other buttons are working

  • Medhat Salem
    Medhat Salem Member Posts: 12 Member

    Picture 2 When I connect the X1 To Traktor pro 2

  • Medhat Salem
    Medhat Salem Member Posts: 12 Member
    https://community.native-instruments.com/discussion/comment/230318#Comment_230318

    Dear UWE read My Post

  • Uwe303
    Uwe303 Moderator Posts: 4,736 mod

    Can you open the preferences and go to the mapping page, then make a screenshot.

  • Medhat Salem
    Medhat Salem Member Posts: 12 Member
    Traktor pro 3.jpg X1.jpg

    Dear UWE here is the screenshot As I understand - Thanks for the reply

  • Uwe303
    Uwe303 Moderator Posts: 4,736 mod

    That looks good, you maybe have to set the midi input and output to that specific controller for that mapping, not to "all ports" like in the first picture.

  • Stevan
    Stevan Traktor Mapping Mod Posts: 2,310 mod

    "All Ports" indicaters you are using it's MIDI mode and not the user mode.

    I just checked TP4 and the X1 Mk1 mapping is still accessible via devices menu.

    image.png
  • Uwe303
    Uwe303 Moderator Posts: 4,736 mod
    https://community.native-instruments.com/discussion/comment/230492#Comment_230492

    So then there should be no port cause it's handled via hid?

  • Medhat Salem
    Medhat Salem Member Posts: 12 Member

    So What is The Solution Dears ?

  • Uwe303
    Uwe303 Moderator Posts: 4,736 mod
    edited 6:53PM

    Can you try to delete that device with "edit - delete" connect the X1 again and add it back as you see above what stevan posted, no need to go into midi mode with shift + hotcue it should work in NHL (not HID) mode. Ou try to use it with TP3 - if i remember correctly it has the "install wizard" in the preferences on the bottom, after deleting that device you could try out the "wizard" if it´s still there. And what exact traktor version du you use?

  • Medhat Salem
    Medhat Salem Member Posts: 12 Member

    Dear UWE , I will Try To Delete The Device and Reinstall it again , My Traktor ver 3.20.60

  • Medhat Salem
    Medhat Salem Member Posts: 12 Member

    Dear UWE - I Removed and Deleted The device and its Components and Drivers and I Reinstalled It Again and it gave me the Same RESULT !

  • Medhat Salem
    Medhat Salem Member Posts: 12 Member

    YES , Perfect UWE , I removed The Controller and I Replaced a Custom TSI File For Mapping and It Works Great , Thank You - I still Have Some Small Issues If I will Not Solve it I will post - Thanks UWE

Back To Top

Categories