Xone K2 Hot Cue Lights Mapping
I am trying to build my own mapping for the xone k2 with Traktor Pro 3.
The xone k2 only outputs 3 LED colors. Here is the behavior I am attempting.
if there is already a hotcue stored in slot 1, then the assigned midi button should light up
is this possible?
this is the behavior on the X1.
thanks!
Comments
-
It is possible... It's fidgety, but possible.
You need to add an OUT to the same button with LED as the type of controller and Interaction mode to output.
Set the controller range Min=0 & Max=1. Midi range stays at Min=0 and Max=127.
Tricky bit number 1 - Make sure you are not using latching layers and to choose your button color (red, green or orange) you need to consult the manual for the corresponding midi note (CC or note detc etc), then manually enter that value into the button value field e.g Ch15.Note.C#1 or what ever the corresponding one is for your button.
Tricky bit number 2 - It doesnt always light up when you start up or connect your K2.. you need to press the button for it to start working sometimes.
1 -
Here is the manual. Page 17+18 for the MIDI Out designations:
0 -
Disable latching layers is a first thing you need to do in order to access all 3 colors in the same layout.
If you share some screenshots of your hotcue commands then you would get a better answer.
1 -
hi
so i tried it and no light turns on. so my first question is, how can i confirm that i am not using latch layers? i'm assuming i am not as i just updated the k2 firmware and the mapping is from scratch.
i've set all the setings you said and there is no light at all. i suspect something is going on with the controller range.
"Min=0 & Max=1. Midi range stays at Min=0 and Max=127"
originally it was Min=0-1 & Max=7. Midi range stays at Min=0 and Max=127
and with the original settings, i would get the desired light but only as long as i was holding the button down.
thanks0 -
here are some screenshots
suggested settings - no light
https://postimg.cc/kV3YDQtc
original settings - light only when pressing button
https://postimg.cc/XZfH5rf00 -
Post some screenshots, we don't know what command are you using to output cues.
Check official A&H youtube channel, you will find info on how to disable layer system.
0 -
checking out the latch info/videos no... screenshots posted in previous comment. thanks!!0
-
The manual i linked describes how to activate and deactivate latching layers.
0 -
You are using incorrect output command.
Add Out --> Track Deck --> Cue --> Hotcue X Type (there is dedicated command for each cue)
0 -
https://www.youtube.com/watch?v=96Kmd8BPiWM&ab_channel=AllenandHeathUK
It is "State 1" of the Latching Layers setup^
0 -
> @Stevan said:
> You are using incorrect output command.
> Add Out --> Track Deck --> Cue --> Hotcue X Type (there is dedicated command for each cue)
that did the trick. thanks again!2
Categories
- All Categories
- 19 Welcome
- 1.5K Hangout
- 60 NI News
- 771 Tech Talks
- 4K Native Access
- 16.3K Komplete
- 2K Komplete General
- 4.3K Komplete Kontrol
- 5.6K Kontakt
- 1.6K Reaktor
- 376 Battery 4
- 833 Guitar Rig & FX
- 425 Massive X & Synths
- 1.3K Other Software & Hardware
- 5.7K Maschine
- 7.2K Traktor
- 7.2K Traktor Software & Hardware
- Check out everything you can do
- Create an account
- See member benefits
- Answer questions
- Ask the community
- See product news
- Connect with creators