Why do I only have two stereo outputs for routing in Konakt 7?

I'm using Kontakt 7 in FL Studio on Mac. I'm trying to route drums out of Kontakt so I can mix them in my DAW but when I go to assign an output it's stereo channels I only have 2 channels for all the outputs. How do I get more? When I add more outputs I still only have two stereo channels for all the outputs. Pls help, Thanks!
Best Answer
-
@[email protected] Sorry for jumping on the issue so late but we do have a Knowledge Base article for that: How to Route KONTAKT to Multiple Outputs in FL Studio
0
Answers
-
Edit: sorry this answer wasn’t correct. Check the one down
1 -
Okay, so how do I set it up so the outputs are set up for my DAW and not my interface.
0 -
Follow these steps to add the outputs to Kontakt:
Push the + button in Outputs to open this menu and follow these settings (in Quantity I put 6, but you put how many outputs you need)
Once the Outputs are set, you open the instrument’s editing menu (wrench icon on top left) and in Group Editor tab you select a different st output for every sound
Then in your DAW you select the different st outputs for every audio track
0 -
So the issue isn't that I can't create outputs, the issue is that I only have 2 stereo channels for ALL of my outputs. I can only route outputs to the same 2 stereo channels 1 and 2. Im attaching a photo of my outputs, look at the channel numbers at the bottom. They all say "1/2" because I only have 2 stereo channels for all of the outputs instead of 2 for each output which would be "1/2 3/4" and so on. I need more stereo channels. And everyone else's says channels are named "Kt. st. 1" in the drop down box but mine say "St 1/2 (1)".
0 -
Your screenshot shows that the outputs FROM Kontakt to your DAW are listed above the fader (in the Kontakt Output Section shown) and the PHYSICAL outputs from your audio interface are 1/2 because you only have TWO HARDWARE outputs available, shown below the fader.
If you had an interface that had multiple hardware outs (1/2, 3/4, ADAT 5/6, 7/8 etc.) they would show as such.
0 -
Did you follow the steps I mentioned? If you do so (with also the “Ascending output assignment) it will automatically create 3/4, 5/6,… and they will be labeled as plugin outputs.
Try it
0 -
@[email protected] Sorry for jumping on the issue so late but we do have a Knowledge Base article for that: How to Route KONTAKT to Multiple Outputs in FL Studio
0 -
am I stupid? there is no wrench in Kontakt 7 anymore...at least I don't see it. can you tell my how I still get access to that menu?
0 -
Even if I would like to stop helping NI with all the job I’m doing here (maybe if they would have to answer all the questions we answer here in their place they would have less time to think to wonderful ideas like putting KK MK1 EOL…) I still want to help users like you and not dump my frustration with the company on fellow users….therefore…:
the problem could be you are in minimize view (which doesn’t show all elements). Check it
0
Categories
- All Categories
- 21 Welcome
- 843 Hangout
- 77 NI News
- 409 Tech Talks
- 1.9K Native Access
- 8.5K Komplete
- 1.1K Komplete General
- 2.1K Komplete Kontrol
- 3.1K Kontakt
- 718 Reaktor
- 248 Battery 4
- 484 Guitar Rig & FX
- 283 Massive X & Synths
- 503 Other Software & Hardware
- 3.4K Maschine
- 23 Sampling Room
- 4.2K Traktor
- 3.9K Traktor Software & Hardware
- Check out everything you can do
- Create an account
- See member benefits
- Answer questions
- Ask the community
- See product news
- Connect with creators