Audio 8 DJ & Multicore timecode

Dannytehe · 2024-03-24T10:26:23+00:00

There was an error rendering this rich post.

Hi !, I have bought a used Audio 8 DJ, I have the Windows 10 (x64) operating system, using the multicore and timecode cables in Traktor 2 scratch pro I receive a very low signal and I cannot calibrate correctly, I have all the correct configuration, correct cable connections and I use everything necessary. I I have tried doing the same using an Audio 6 mk1 using normal rca cables and I receive a good signal to calibrate timecode.

I have looked to see if there are Audio 8 DJ drivers available for my Windows 10 operating system and there are none available for download, there are only up to Windows 8

My question is: is it possible that I am not receiving the correct signal for timecode due to incompatibility with my operating system?, where can I find drivers for Windows 10 (x64)?, I hope you can help me please, thank you, regards.

Find more posts tagged with

Traktor Pro 2

Accepted answers

All comments

Heboracing2

Audio 8 is not longer supoorted from Ni. Switch to an audio 6 or 10 with MK2 Timecode Signal

lord-carlos

The audio 8 should still work on windows, even though it's no longer supported.

Is the pre-amp on?

Dannytehe

https://community.native-instruments.com/discussion/comment/143437#Comment_143437

What is “pre-amp” ?

Dannytehe

I have tried connecting the cables from my turntable directly to the audio 8 and it calibrates well, it seems that the multicore cables are in bad condition (I am surprised that they both fail) or the problem may be that the latest version of the audio 8 driver is not compatible for multicore cables in Windows 10

lord-carlos

I don't know how exactly it works, but the input mode toggle has to be set to DVS vinyl, and not line level. If the light on the top is yellow it means it's set to CD/Line mode. Orange is phono mode, and green is timecode vinyl mode. You want green. That will boost the signal by +18 dB

Also only channel 1,2 and 3,4 support phono if I understand the manual right.

Dannytehe

https://community.native-instruments.com/discussion/comment/143444#Comment_143444

So I have it configured, I put it on phono and on vinyl control and there is no good signal and it does not calibrate

lord-carlos

Is there a difference in signal strength you see in traktor between phono and vinyl control mode? The little bar that shows up in input routing.

And can you share a screenshot of the scope?

Dannytehe

there is no difference between phono and “control vinyl”, low signal in both.

I have followed the steps in this tutorial to make the connections of my multicore cable, I have done everything correctly:

lord-carlos

Almost looks like no input at all.

Dannytehe

https://community.native-instruments.com/discussion/comment/143495#Comment_143495

there is no difference between phono and “control vinyl”, low signal in both.

I have followed the steps in this tutorial to make the connections of my multicore cable, I have done everything correctly:

is possible multicore cables may be in bad condition

lord-carlos

Maybe. Just try with regular cables?

Dannytehe

https://community.native-instruments.com/discussion/comment/143503#Comment_143503

there is no difference between phono and “control vinyl”, low signal in both.

I have followed the steps in this tutorial to make the connections of my multicore cable, I have done everything correctly:

With normal cables everything works correctly, but I want to use multicore cables

lord-carlos

It works with regular cables and a8?

Well then we know the interface and software is working.

Maybe you connected them wrong?

Dannytehe

https://community.native-instruments.com/discussion/comment/143523#Comment_143523

The cables are well connected: the “mixer line in” cable in “line in” of my mixer, the “mixer t t/cd” cable in “phono in” of my mixer, the “audio 8 DJ input” cable in “In channel A” of audio 8, the “audio 8 output” cable in “out channel A”, all this repeated with the second turntable.

Dannytehe

Works with normal cables and a8, yes

Quick links

Unanswered questions