Why is Monark Sound not saved

13»

Comments

  • gorogne
    gorogne Member Posts: 36 Member

    Hello again, is it actually possible to use this beta? Unfortunately, the support is not very helpful and does not respond.

  • ozon
    ozon Member Posts: 2,005 Expert
    https://community.native-instruments.com/discussion/comment/196895#Comment_196895

    I have the current public release installed on mine.

    If anything, it would have been a change (like writing similar into a config file) that was introduced by one of the previous beta versions. Those are not available anymore.

  • andreat668
    andreat668 Member Posts: 4 Member
    edited February 7

    bumping this thread as I started having the same issue as the Op.

    Basically I load up the preset “Autobass” in monark, save the project within the monark preset, opening back the project and the preset “Autobass” sounds like the monark init patch..

    I have the maschine plus since 2021 and never had this issue until 2 weeks ago.

    Wondering if the SD card play a role in this.

  • andreat668
    andreat668 Member Posts: 4 Member

    I even saved the Autobass preset in my user folder but when I load it up within the project I got same results.

    Pretty annoying I would say.

  • gorogne
    gorogne Member Posts: 36 Member

    It would be great if you could also write to support so that they can finally get this problem under control.

  • gorogne
    gorogne Member Posts: 36 Member
    https://community.native-instruments.com/discussion/comment/209648#Comment_209648

    It would be great if you could also write to support so that they can finally get this problem under control.

  • andreat668
    andreat668 Member Posts: 4 Member
    https://community.native-instruments.com/discussion/comment/209723#Comment_209723

    Sorry to get back to you only now, crazy busy at work plus I had to get focused on couple releases as well.
    By the way for now the issue seems sorted almost completely from my side, what I have done:
    1 - Factory reset my unit, it also did (I think) a firmware update just right before the reset.
    2 - Take out the SD card, save all my stuff and erase and format the card as well.

    Now the Monark patches values seems recalling correctly, if I save the tweaked patch it recalls as well when a project is loaded back.
    But I tested this only with the factory Manark patches from the Maschine 2 library, I guess it will work with my user patches as well.
    I think I had so many Maschine expansion plus a ton of user content data and maybe the SD got corrupted in some way.
    Hopefully doing the factory reset plus the sd card format will fix your unit as well.

  • gorogne
    gorogne Member Posts: 36 Member

    Hello, unfortunately this has not solved my problem. Thanks for your tip though.
    Perhaps you could try again to see if “A train” (the second/lower in the list) is now behaving normally for you.
    That would be cool.
    And which version do you have now? I have system version 1.5.1.0, machine version 2.17.5.(R0), firmware 0.1.9

  • Kymeia
    Kymeia NKS User Library Mod Posts: 5,616 mod
    https://community.native-instruments.com/discussion/comment/195663#Comment_195663

    If that’s the case that’s good then because it probably means whatever was causing it is fixed already

  • ozon
    ozon Member Posts: 2,005 Expert
    https://community.native-instruments.com/discussion/comment/219878#Comment_219878

    No. That would have been the pre 1.5.1 beta.

  • gorogne
    gorogne Member Posts: 36 Member

    Could it be that the file system on my SD card is the wrong one? I am using exFAT?

  • ozon
    ozon Member Posts: 2,005 Expert
    https://community.native-instruments.com/discussion/comment/220735#Comment_220735

    If it was a file system issue, I would expect an impact on write operations in general not just saving sound settings wthin a Project.

Back To Top

Categories