Read our community note - here.
Maschine Plus 1.4 update is out now!
Comments
-
Can you elaborate on this? What is Autoloop and where would I find it?
cheers!
0 -
In the menu where you'd normalize or truncate a sample. We've always had the option to set loop points on a sample; but now it has an option to do it automatically.
It would make the most sense if you were sampling a single note from a synth. Set loop points and it can sustain forever. Mess with adsr to shape it as you see fit.
...but I just spent <way too much time> doing the same thing with my voice. I'm the oscillator now.
I have quite a few complaints about the sampler in maschine; but I also think there's not enough discussion about it. You can make a lot of different sounds if you treat the sampling engine as a synth. Autoloop can get you there faster.
3 -
Is there any time limit on having fun and being inspired?:) I got 2 kids and a house, that’s my limit, otherwise I love getting lost hahahaha
1 -
Thanks! How can I miss that? Already updated, will check everything today.
0 -
Thanks! How can I miss that? Already updated, will check everything today.
0 -
I'm looking for this autoloop option in the sample edit menu in Maschine 2.15.1 software, but i cannot find it? Can you help me out?
0 -
Where can I rename the recorded sample? I couldn’t find it. Tried saving as but that only saves the sound and not the sample. Or am I missing something?
0 -
When in the autosampler it is under batch process. Just scroll over to the right.
The order of sections is : recording, input, note map, velocity map, batch process, monitor
Turn FIND LOOP on
🤙🏾
2 -
Ahhh. I thought it was also a new option under regular sample edit?
0 -
Was this a big project ? With a lot of instruments or fxs ? Let us know what happens with the copied project.
0 -
Yes it is 😅 I thought you were having issues finding it on autosampler lol. But it is also under sample edit. Click SAMPLING button on your Maschine then hit the EDIT tab then use the buttons to scroll over to AUTO LOOP
If your on software it's slightly different. The autoloop is normally on already just need to adjust parameters. The parameters are under LOOP (active, start, end, xfade)
0 -
I ran into some issues yesterday with both projects I started in standalone mode after updating. They were both going good until they started freezing/crashing continuously. Every time I hit restore project it would come back and freeze/crash immediately. They were both smaller projects with barely any FX. Just 1 and/or 2 auto-sampled instrument patches, Bass Synth, Expansion Kit and a Group with Perform FX with all of the tracks outputs routed to it. The CPU was between 30-50% on both before they froze. I’ll also add that I was clocked as the master with my friend’s MPC live and I had a Novation Launchpad set up for triggering scenes and locks. Not there sure if that has anything to do with it or not.
Update: I just loaded the projects onto my computer and they work fine thankfully
0 -
(edit: right click and "find loop". Leaving my original response since it shows what autoloop actually does)
Quite interesting they didn't seem to give a way to access it from the software.
GIF of selecting a sample, using the hardware to setup autoloop and then changing to ADSR. It selects the loop points for you. There would be an "autoloop" before "truncate" if setup the same way as the hardware.
Frankly, not a fan of not having the hardware and software 1:1, but whatever.
1 -
It's not very intuitive. Hold shift while on the "Record" tab of the sampling page. If you've recorded or loaded a sample and made edits, you need to go back to the "Record" tab and use previous/next to select the sample you want to rename.
I've not figured out a way to make edits to the sample and then rename the one you edited. So if you're recording stuff.
- Record the sample
- Rename it immediately
- Then go edit.
If you record the sample, go trim it and then go back to rename, you're back to working with the original sample (i.e. before you trimmed it)
1 -
Hello @Jeremy_NI
This was the last project I did before the update. not very advanced, it launched after several attempts or behind other project launches, even the copied one.
I formatted the SD card and reset the M+, and everything works perfectly the first time now.
Thank you
1
Categories
- All Categories
- 19 Welcome
- 1.6K Hangout
- 66 NI News
- 843 Tech Talks
- 4.3K Native Access
- 17.3K Komplete
- 2.1K Komplete General
- 4.5K Komplete Kontrol
- 6K Kontakt
- 1.6K Reaktor
- 395 Battery 4
- 882 Guitar Rig & FX
- 447 Massive X & Synths
- 1.4K Other Software & Hardware
- 6.1K Maschine
- 7.7K Traktor
- 7.7K Traktor Software & Hardware
- Check out everything you can do
- Create an account
- See member benefits
- Answer questions
- Ask the community
- See product news
- Connect with creators