im wondering where I can find a rubber foot for maschine jam.
Answers
-
Amazon has dozens probably of hundreds of different types if that's an option for you. I'm not sure where you live, but someplace like Target or Walmart should have a few types as well. Of course a hardware store like Lowes or Home Depot would probably have more variety. Again I'm not sure what country you live it, so whatever the equivalent of those stores in your country would be a good place to start.
1 -
From a quick Google, it looks to be a very specific design of foot (more like a pad) rather than a typical hardware store item.
The image I found showed that it has a central hole or insert with what looks like a brass thread in the middle.
The Maschine "feet" (pads) are also uniquely designed with two little pips on each one, to locate it into the base.
0 -
Even if it's a specific foot, An option is to remove the 3 remaining feet and just replace with a new 4 set of rubber feet whatever the shape, 4 of the same should make it even, ( or 2 if one size in front, and 2 of another size in the back) add some super glue and get Crafty🎉
1 -
NI doesn't sell a lot of spare parts, only knob caps I think, so you're on your own.
Personally, I'd do what @reffahcs said, there's tons of rubber feet out there, some with a hole in the middle, and tons of adhesive ones of all sizes and shapes. I would remove the OG's ones and buy a set of 4 or 6, it's dirt cheap too.
1 -
thats what i would do too... i have a 3 rubber footings on my Maschine Jam too, and as im missing the front rubber foot, i just hang the end of the rubber footing off the edge of my table providing stability... otherwise i would just remove the opposite side, and make it a 2 legged rubberfooted MJam lol
alternatively one could do a frankenstein rubberfoot and cut on off another device and glue it underneath *shrugs
0 -
haha i do agree. i do have a glue gun and glue and im crafty. i could 100% red green it to be even better.(lol)
and i really do appreciate everybodys feedback. its neat to know theres really not allot of options for that.
you cant blame me for just wanting the exact one thats supposed to be there though.
the plan is to to have the m+ and the jam on a wooden degree angled table just big enough for both of them,
i could always just notch something on the actual platform its going to be on in the position it will be sat into aswell.
but you know if i worked at NI and happened to seen this post id probably send me a message letting myself know i have a few of them spare kicking around in the shop id be happy to send me. hint hint :P
1 -
1/3 full pack of zig zaggs is actually doing its justice.
1 -
Also, one could use enclosed stand. That way two of rubber feet are in the air. One may use one of them to replace missing front rubber foot.
Have a look at other pictures at this web page.
0 -
The fixture that raises the back up?
0 -
Yes. It is quite handy anyway as Jam is little up at the back.
1
Categories
- All Categories
- 19 Welcome
- 1.4K Hangout
- 60 NI News
- 764 Tech Talks
- 4K Native Access
- 16.3K Komplete
- 2K Komplete General
- 4.3K Komplete Kontrol
- 5.6K Kontakt
- 1.6K Reaktor
- 374 Battery 4
- 833 Guitar Rig & FX
- 424 Massive X & Synths
- 1.2K Other Software & Hardware
- 5.7K Maschine
- 7.2K Traktor
- 7.2K Traktor Software & Hardware
- Check out everything you can do
- Create an account
- See member benefits
- Answer questions
- Ask the community
- See product news
- Connect with creators