Wich driver for cubase 13 Kontrol S25

Tom De Clercq

Hello,

I just bought cubase 13.

I have installed the driver for Audio 6, this works 100%

Wich driver i have to use for kontrol S25? i have tried all drivers on you site, but nothings works.

I it possible that the driver for audio 6 and kontrol S25 creates a conflict?

Thanks for you help

rgrds

Tom

Tom De Clercq

Uwe,

I have found it, the problem was that i did not have adapted the midi inputs.

Thx a lot!

@all thank you!

Uwe303

Hello,

you just install komplete kontrol, the driver and implementation should then be there. So the keyboard should then work after adding it in cubase settings as control device like shown in the manual.

Sunborn

https://community.native-instruments.com/discussion/21261/wich-driver-for-cubase-13-kontrol-s25

Which S25? mk1, mk2, mk3?

and what operating system?

"tried all drivers" ...there are just 2 versions, one for the mk1 and one for the mk2 and both are for Windows.. if you are on Mac, you do not need any driver (however, make sure that you do the firmware update, only if needed though!)

https://www.native-instruments.com/en/support/downloads/drivers-other-files/

Tom De Clercq

Hello,

Its the MK1, my system is windows 11

See the print screens below, when i install the driver for audio 6, i dont have any midi out on my cubase...

Jeremy_NI

@Tom De Clercq It's not clear what you are trying to achieve here? What do you mean by "nothing works"?

Do you want to setup Komplete Kontrol host integration in Cubase? Then please follow these steps: How to Integrate Your Kontrol Keyboard with Your DAW

Or are you not able to play notes from the S25 in Cubase?

Is everything functional in Komplete Kontrol in standalone?

Uwe303

https://community.native-instruments.com/discussion/comment/124379#Comment_124379

You have enabled too much midi devices there, you only need there midi in komplete kontrol - 1, some in/outputs like from the audio interface or Komplete - ext only if you have connected there some external gear, via those midi din plugs. And the daw port you need for the DAW integration under remote device legacy (transport and alike) see the above linked article.

try it like that

Tom De Clercq

Thank you for the feedback Uwe,

I do not use external midi, only vst plugin synths.

I send you below my screens of what i have done, bur i'm still not get a result

Thanks for you help

rgrds,

Tom

Uwe303

https://community.native-instruments.com/discussion/comment/124441#Comment_124441

so first you have to disable too the daw port under midi port setup, those ports will still work for remote control, maybe that´s a bit counterintuitive.

Then what is exactly the problem, do you get no midi signal from the keys, do you get overall no sound. Please elaborate a bit more what the issue is. With the " in all midi" option you normally play the selected midi instrument, of course if you don´t have changed the standard in the channel to something other than all midi in" like so for example:

Kubrak

Also, if you want use Komplete Kontrol SW and S25 to full strength (not cripled to just plain MIDI controller), you must use pre 3.0 version....

Jeremy_NI

@Kubrak Thanks! I totally overlooked that detail 🤦‍♂️

@Tom De Clercq Please make sure you install this version of Komplete Kontrol: Komplete Kontrol 2.9.6 (Windows)

More info here:Notes on Ending Software Support for Komplete Kontrol S-Series MK1 Keyboards

Tom De Clercq

Uwe,

I have found it, the problem was that i did not have adapted the midi inputs.

Thx a lot!

@all thank you!

Uwe303

Ok - then I hope you'll have a lot of fun now, you're always welcome.

Tom De Clercq

Hello Uwe,

When i play my project i get clicks/noises via my audiocard.

More on the audio files, but also on the vst instruments.

I think dis has something to do with the settings?

Uwe303

https://community.native-instruments.com/discussion/comment/125202#Comment_125202

Please make a new thread you can mark me, or others, by typing @ and then the name, then you can also make a picture of the interface settings under the studio/studio settings/audio system, there you have a control panel button, press it and make there the picture from the K6 audio interface settings.