M-Audio Expression pedal not working with S88 Mk3
The M-Audio EX-P is on the supported pedals list. I own 3 of them. They work with my other gear. They do not with the S88 Mk3. Neither at the expression port nor the other 2 ports.
I've tried all the combinations (ring, tip, polarity, switch on the Ex-p, etc.) No output.
Now what?
Help!
Jochen
Best Answer
-
I finally got it working. During calibration when it says press down I left the pedal full up (heel) and then when it says move pedal all the way up I press down on the pedal (toes). I'm using the M-Audio EX-P pedal, currently in the Expression pedal socket.
1
Answers
-
Same problem here.
0 -
The EX-P works fine.
Have you calibrated it in the Pedal Settings page?
Make sure select Continuous, and then follow the calibration steps on-screen (triggered by the button in the top right).
0 -
Thank you, I'll check it on Wednesday.
0 -
I've had the same issue myself. Looking at the MIDI monitor I saw some traffic, but after trying to calibrate there's just nothing.
@Matthew_NI can you recommend a known working config? There's a switch setting on the bottom for M-Audio or Other and a dial on the side, then there's various inverse and tip/ring settings in the actual piano config. I used MIDI Monitor on my Mac to try and troubleshoot things but it wasn't super helpful.
Can you add to NI's already long list of TODOs, some sort of real time pedal value ouput to the keyboard display? Something that regardless of the software instrument being used, I could look at and at least say yes/no the pedal is working or not working? Right now we don't really have anything. And between the switch on the bottom, the knob on the side, the inverse setting on the keyboard and the tip/ring setting on the keyboard, it's just really a lot to try and go through. I called it quits earlier tonight and just figured I'd look at it another time.
5 -
I tried every combination on 3 different EX-Ps. Nothing produced any midi traffic.
0 -
Plus calibrations.
0 -
It depends on each pedal.
Firstly, you have four ports. Sustain, Expression, Assign 1, Assign 2. Although the first two ports are configured by default for most pedals, any ports can be anything. So, select whichever port using rotary #1
Secondly, using rotary #3, select Continuous as your pedal type.
Thirdly, select Calibrate using button #8 above the screen. Follow the steps to calibrate (e.g. down/toe, up/heel).
Fourthly, if that hasn't worked, set the relevant Invert or Swap settings for your particular pedal. If it has a manual, it may say which one to use.
Lastly, assuming you want it to send Expression, make sure the following page (left/right arrows) is set correctly.
1 -
Well I don't know what to make if this right now. I tried a bunch of stuff and finally switched from MIDI 2.0 back to MIDI 1.0 and it seemed to start working. In the middle of writing this post the pedal just stopped working. I tried it in a Arturia Keystep 37 (#notsponsored) as a sanity check just to test the pedal and it worked fine.
I have it plugged into the sustain pedal input and it worked in both switch and continuous modes. Then only switch and now nothing.
Can you confirm if the keyboard supports TRS pedal plugs? I've had other audio equipment where the tolerances were just ever so off that the device wouldn't work when fully inserted. Kinda seems like this might be what's happening here?
At 00:52 it finally stopped responding (again), I left MIDI Monitor running and as suspected, as I pulled out the connector of the M-Audio pedal, the keyboard finally detected a signal. So..... TS pedals only? Or is there something else going on?
0 -
It supports TRS pedals, of course.
What is your system configuration (e.g. OS version, etc)?
0 -
M2 Studio, MacOS 14.1.1. NI software is all running the latest updates available from the NA installer.
I tried the pedal in the Pedal Assign 2 socket and it works in switch mode but not in continuous. I've verified that all settings (minus using Pedal Assign 2 instead of 1) are the same as the screenshots you posted. When I change the mode to continuous MIDI monitor does not display any activity when moving the pedal.
I also tried opening Komplete Kontrol as well and loading up and instrument, but it does not seem to impact the MIDI pedal. It doesn't say in the manual, at least that I could see, hence the question. I just wanted to make sure that I wasn't supposed to be using a pedal with a TS connector instead of a TRS.
0 -
I finally got it working. During calibration when it says press down I left the pedal full up (heel) and then when it says move pedal all the way up I press down on the pedal (toes). I'm using the M-Audio EX-P pedal, currently in the Expression pedal socket.
1 -
This is the way to get it working. Settings are: Mode continuous, Invert off, Swap Tip.
Thank you raffahcs for ignoring prompts and making it work :-)
0 -
I tried all the various invert/swap configurations without luck. For my specific pedal, the M-Audio EX-P, the only thing that worked was using the opposite pedal position during the calibration routine than what the instructions called for. In other words, pedal down instead of up and up instead of down. I left the invert to off and the swap to ring as originally suggested by @Matthew_NI
I also tried switching the switch on the bottom of the pedal and it did not make a meaningful difference.
0 -
We are going to change those instructions, as there has been a lot of confusion about what constitutes up, and what constitutes down.
There have been several users thinking the "opposite" is what worked - but it's confusing nomenclature.
I think we can just replace it with a graphic so there can be no confusion.
1 -
That would be awesome!
0
Categories
- All Categories
- 19 Welcome
- 1.4K Hangout
- 60 NI News
- 735 Tech Talks
- 3.9K Native Access
- 15.9K Komplete
- 1.9K Komplete General
- 4.1K Komplete Kontrol
- 5.5K Kontakt
- 1.5K Reaktor
- 364 Battery 4
- 817 Guitar Rig & FX
- 416 Massive X & Synths
- 1.2K Other Software & Hardware
- 5.5K Maschine
- 7K Traktor
- 7K Traktor Software & Hardware
- Check out everything you can do
- Create an account
- See member benefits
- Answer questions
- Ask the community
- See product news
- Connect with creators