X1 MK3: How add a new mode page to mode select button ?

sambenito
sambenito Member Posts: 2 Member
in Traktor Software & Hardware

The mapping that came with the controller x1 mk3 ( firmware 0.2.7) is very poore, so,

how can add new modes pages to the mode select button at device top to access different section of traktor, for example, the looper, the recorder, maybe one full deck parameters like filter, gain, master tempo, one page for remix decks, etc..

I only see the midi mode with shift , but just one page for everything is difficult, would be better one page for secctions of the traktor

is that possible ?

Tagged:

Best Answers

  • Sûlherokhh
    Sûlherokhh Member, Traktor Mapping Mod Posts: 2,827 mod
    Answer ✓

    It's possible. I am working on a stem control mode for the x1, although work has progressed with many interruptions. You can check my signature (below my post) for a community mod to improve overall performance of the controller by adjusting the qml-code (basic mapping) of the x1.

    It's doable but unless you bring some basic programming skills (in any language) it's hard to get started.

    If you are using midi mode, you can design several overlays to cycle through using modifiers. As above, basic understanding in boolean logic is very helpful.

  • Sûlherokhh
    Sûlherokhh Member, Traktor Mapping Mod Posts: 2,827 mod
    Answer ✓

    So, you haven't read the post, just skimmed it.

    The first mod incorporates the browse mode and has the most comprehensive overhaul, 1 file for TP3.11.1, 1 file for TP4.0.2

    The second mod (the minimal mod) leaves out the browse mode and most additions, fixes the tempo control and removes the mixer overlay (only FX switches with the mode button), again 1 file for TP3.11.1, 1 file for TP4.0.2

    Everything below that are mods for TP3.10, when the X1 was just introduced and can be completely ignored. I should just remove that section i suppose, to remove the confusion.

    You only download a single pack (that contains a folder with many files) from among the first two variants. Please read the installation instructions at the top so you don't have to reinstall traktor.

Answers

  • Sûlherokhh
    Sûlherokhh Member, Traktor Mapping Mod Posts: 2,827 mod
    Answer ✓

    It's possible. I am working on a stem control mode for the x1, although work has progressed with many interruptions. You can check my signature (below my post) for a community mod to improve overall performance of the controller by adjusting the qml-code (basic mapping) of the x1.

    It's doable but unless you bring some basic programming skills (in any language) it's hard to get started.

    If you are using midi mode, you can design several overlays to cycle through using modifiers. As above, basic understanding in boolean logic is very helpful.

  • sambenito
    sambenito Member Posts: 2 Member

    thanks..I see that there are several files, is there one that integrates them all or do I upload them one by one? Or where is the list of all these mappings / patches?

  • Sûlherokhh
    Sûlherokhh Member, Traktor Mapping Mod Posts: 2,827 mod
    Answer ✓

    So, you haven't read the post, just skimmed it.

    The first mod incorporates the browse mode and has the most comprehensive overhaul, 1 file for TP3.11.1, 1 file for TP4.0.2

    The second mod (the minimal mod) leaves out the browse mode and most additions, fixes the tempo control and removes the mixer overlay (only FX switches with the mode button), again 1 file for TP3.11.1, 1 file for TP4.0.2

    Everything below that are mods for TP3.10, when the X1 was just introduced and can be completely ignored. I should just remove that section i suppose, to remove the confusion.

    You only download a single pack (that contains a folder with many files) from among the first two variants. Please read the installation instructions at the top so you don't have to reinstall traktor.

Back To Top

Categories